ENGINE UPDATE NOISE DIAGNOSIS INFORMATION

I.EXHAUST MANIFOLD BOLTS A NEW EXHAUST MANIFOLD TO CYLINDER HEAD BOLT (P/N 1626193) IS AVAILABLE FROM GMWDD. THIS NEW BOLT INCORPORATES A TORQUE PREVAILING FEATURE AND SHOULD BE USED WHEN SERVICING LOOSE EXHAUST MANIFOLD BOLTS ON HT4100 ENGINES. II.OIL ECONOMY THE FOLLOWING INFORMATION WILL PROVIDE ASSISTANCE WHEN ASSESSING AND DIAGNOSING HT4100 ENGINE OIL CONSUMPTION CONDITIONS: A.GENERAL INFORMATION 1.WHEN A COMMENT CONCERNING OIL ECONOMY IS RECEIVED, THE INFORMATION PROVIDED BY THE OWNER SHOULD BE NOTED. 2.SOME DRAIN BACK TIME IS REQUIRED AFTER STOPPING THE ENGINE BEFORE AN ACCURATE DIPSTICK READING CAN BE OBTAINED. ABOUT 2-3 MINUTES WOULD APPEAR TO BE THE MINIMUM. FIVE TO 10 MINUTES IS OPTIMUM. 3.SOMETIMES SHORT FILLS OCCUR IN PRODUCTION. IF A CAR IS DELIVERED THIS WAY, THE OWNER MAY ASSUME AN ECONOMY CONDITION EXISTS THE FIRST TIME THE OIL IS CHECKED. 4.DETERMINE THAT THE PROPER VISCOSITY OIL IS BEING USED. THIN OILS HAVE HIGHER CONSUMPTION RATES THAN THICKER ONES. 5.A CAREFUL INSPECTION SHOULD BE MADE OF THE PCV SYSTEM. AN UNSEATED PCV VALVE OR KINKED OR COLLAPSED HOSE CAN CAUSE EXCESSIVE OIL CONSUMPTION. A RESTRICTED PCV SYSTEM CAN ALSO CAUSE RAPID OIL DETERIORATION AND POSSIBLE PREMATURE WEAR TO THE CAMSHAFT AND VALVE LIFTERS. CHANGING THE VALVE AND/OR HOSE IS USUALLY THE CORRECTION. OIL ACCUMULATION IN THE AIR CLEANER AND EXCESSIVE WETTING OF THE ELEMENT IS A CLUE THAT THE PCV SYSTEM SHOULD BE CAREFULLY INSPECTED. 6.A CONTROLLED TEST SHOULD BE INITIATED AFTER IT IS VERIFIED THAT THE OIL ECONOMY CONDITION IS NOT DUE TO EXTERNAL LEAKAGE OR ANY OF THE ABOVE. 7.AT LEAST 3,000 MILES ARE NORMALLY REQUIRED TO OBTAIN A VALID TEST OF THE OIL ECONOMY. AN EXCEPTION TO THIS WOULD BE GROSS CONSUMPTION CASES OF 500 MILES/QUART OR LESS THAT INDICATE A SERIOUS CONDITION EXISTS AND IMMEDIATE CORRECTIVE MEASURES SHOULD BE TAKEN. B.WHAT TO LOOK FOR WHEN DIAGNOSING AN ENGINE AFTER VERIFYING THAT EXCESSIVE OIL CONSUMPTION IS OCCURRING: 1.A LOOSE INTAKE MANIFOLD ALLOWS OIL TO BE DRAWN INTO EITHER THE INTAKE PORTS OR EXHAUST HEAT CROSSOVER PASSAGES RESULTING IN EXCESSIVE CONSUMPTION. 2.PISTON RINGS: A.COMPRESSION RING GAPS LINED UP-PARTICULARLY ON SEVERAL CYLINDERS. B.MISSING OR BROKEN PISTON RINGS. C.OIL RING EXPANDER MISSING OR OVERLAPPED AND NOT EXERTING PRESSURE ON THE OIL RING RAILS. D.PISTON RINGS (I.E., COMPRESSION RING) INSTALLED UPSIDE DOWN-THE DIMPLES SHOULD ALWAYS BE ON THE TOP. E.RINGS STUCK IN THE GROOVES OR EXCESSIVE SIDE CLEARANCE. F.SCUFFED RINGS OR SCORED BORES (USUALLY GO TOGETHER). 3.MISMACHINED CYLINDER-THIS WOULD BE OBSERVED VISUALLY AS A LOW SPOT WHERE THE RINGS FAILED TO CONTACT THE CYLINDER WALL OR MANY SMALL HOLES IN THE BORED SURFACE OR A CYLINDER THAT WAS BORED OVERSIZED AND ONLY PARTIALLY HONED (I.E., BORING TOOL MARKS SHOWING). 4.MISSING OR BROKEN VALVE STEM SEALS-PARTICULARLY ON THE INTAKE VALVES. 5.EXCESSIVE VALVE GUIDE WEAR-PARTICULARLY ON THE INTAKE VALVE GUIDES. III.ENGINE NOISE THE FOLLOWING INFORMATION WILL SUPPLEMENT THE 1982 CADILLAC SERVICE INFORMATION MANUAL WHEN DIAGNOSING AND CORRECTING INTERNAL HT4100 ENGINE NOISES. WHEN DIAGNOSING A SUSPECTED ENGINE NOISE, THE ACCESSORIES AND DRIVE BELTS SHOULD BE INVESTIGATED AS A POSSIBLE SOURCE OF THE NOISE. LOOSE ACCESSORIES AND/OR MOUNTING BRACKETS OR OVERTENSIONED BELTS MAY CAUSE A NOISE WHICH COULD BE MISDIAGNOSED AS AN INTERNAL ENGINE NOISE. THE INFORMATION CONTAINED IN SERVICEMAN BULLETIN 82-21, GROUP 6A, SHOULD ALSO BE REVIEWED TO ASSURE THAT THE NOISE IS NOT ORIGINATING FROM THE FLEXPLATE-TO-CRANKSHAFT ATTACHMENT. A."PISTON SLAP", "METALLIC KNOCK", AND "MALLET" NOISES THREE TYPES OF INTERNAL KNOCKING NOISES REPORTED ON HT4100 ENGINES ARE: 1.A "PISTON SLAP" NOISE CAUSED BY INCORRECT PISTON SIZE OR POSITION. THIS NOISE IS LOUDER ON A COLD ENGINE AND CAN NORMALLY BE REDUCED OR ELIMINATED BY BRIEFLY "SHORTING OUT" CYLINDERS ONE AT A TIME WITH THE ENGINE RUNNING. 2.A "METALLIC KNOCK" TYPE NOISE CAUSED BY CONTACT BETWEEN THE PISTON SKIRT(S) AND THE COUNTERBALANCE WEIGHT(S) ON THE CRANKSHAFT. NUMBER 1, 2, 3, 6, 7 AND 8 PISTON SKIRTS ARE DESIGNED TO OPERATE CLOSE TO THE CRANKSHAFT COUNTERWEIGHTS ON THE HT4100 ENGINE AND MAY CONTACT EACH OTHER AS THE ALUMINUM PISTONS EXPAND DUE TO NORMAL ENGINE TEMPERATURE INCREASES. THIS NOISE IS USUALLY MORE PREVALENT ON A HOT ENGINE AND CANNOT BE SHORTED OUT. THIS TYPE OF CONTACT SHOULD BE VISIBLE AS A NOTCH OR CUT IN THE AFFECTED PISTON SKIRT(S). 3.A "MALLET" TYPE NOISE THAT MAY SOUND SOMEWHAT HOLLOW MAY ALSO BE CAUSED BY INTERFERENCE BETWEEN THE PISTON SKIRTS AND THE COUNTERBALANCE WEIGHTS. THE AFFECTED PISTONS, NUMBER 1, 2, 3, 6, 7 AND/OR 8, MAY NOT SHOW VISIBLE SIGNS OF CONTACT. THIS NOISE WILL NORMALLY BE MORE APPARENT ON A HOT ENGINE BETWEEN SPEEDS OF 800 AND 1400 RPM UNDER VERY LIGHT ACCELERATION FROM A STOP. DISCONNECTING THE EST CONNECTOR UNDER THESE CONDITIONS MAY CHANGE OR ELIMINATE THIS NOISE. THE SERVICE PROCEDURE LISTED BELOW SHOULD BE USED TO CORRECT ANY HT4100 ENGINE NOISES CAUSED BY INCORRECT PISTON AND/OR PISTON SKIRT/CRANKSHAFT INTERFERENCE: ** SEE BULLETIN FOR ADDITIONAL INFORMATION **

General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.