Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Power Tilt and Telescope,Column Shift
- Align the block tooth on the steering shaft assembly (1) to the 12 o'clock position.
- If installing the existing inflatable restraint steering wheel module coil it must be centered first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .
- Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
- Slide the inflatable restraint steering wheel module coil (4) onto the steering shaft assembly (2).
- Firmly seat the retaining ring (3) into the groove on the steering shaft assembly (2).
- Remove and discard the centering tab from the new inflatable restraint steering wheel module coil (4).
- Connect the connector of the inflatable restraint steering wheel module coil to the wire harness assembly.
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
Caution: Improper routing of the wire harness assembly may damage the inflatable restraint steering wheel module coil. This may result in a malfunction of the coil, which may cause personal injury.
Important: A new inflatable restraint steering wheel module coil is pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.
Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Power Tilt and Telescope, Floor Shift
- Align the block tooth on the steering shaft assembly (1) to the 12 o'clock position.
- If installing the existing inflatable restraint steering wheel module coil it must be centered first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .
- Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
- Slide the inflatable restraint steering wheel module coil (4) onto the steering shaft assembly (2).
- Firmly seat the retaining ring (3) into the groove on the steering shaft assembly (2).
- Remove and discard the centering tab from the new inflatable restraint steering wheel module coil (4).
- Connect the connector of the inflatable restraint steering wheel module coil to the wire harness assembly.
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
Caution: Improper routing of the wire harness assembly may damage the inflatable restraint steering wheel module coil. This may result in a malfunction of the coil, which may cause personal injury.
Important: A new inflatable restraint steering wheel module coil is pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.
Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Manual Tilt, Floor Shift
- Align the block tooth on the steering shaft assembly (1) to the 12 o'clock position.
- If installing the existing inflatable restraint steering wheel module coil it must be centered first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .
- Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
- Slide the inflatable restraint steering wheel module coil (4) onto the steering shaft assembly (2).
- Firmly seat the retaining ring (3) into the groove on the steering shaft assembly (2).
- Remove and discard the centering tab from the new inflatable restraint steering wheel module coil (4).
- Connect the connector of the inflatable restraint steering wheel module coil to the wire harness assembly.
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
Caution: Improper routing of the wire harness assembly may damage the inflatable restraint steering wheel module coil. This may result in a malfunction of the coil, which may cause personal injury.
Important: A new inflatable restraint steering wheel module coil is pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.
Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Manual Tilt, Column Shift
- Align the block tooth on the steering shaft assembly (1) to the 12 o'clock position.
- If installing the existing inflatable restraint steering wheel module coil it must be centered first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .
- Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
- Slide the inflatable restraint steering wheel module coil (4) onto the steering shaft assembly (2).
- Firmly seat the retaining ring (3) into the groove on the steering shaft assembly (2).
- Remove and discard the centering tab from the new inflatable restraint steering wheel module coil (4).
- Connect the connector of the inflatable restraint steering wheel module coil to the wire harness assembly.
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
Caution: Improper routing of the wire harness assembly may damage the inflatable restraint steering wheel module coil. This may result in a malfunction of the coil, which may cause personal injury.
Important: A new inflatable restraint steering wheel module coil is pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.
