Inside Rearview Mirror with the Automatic Day-Night Feature System
Components
The inside rearview mirror with the automatic day-night feature system
consist of the following components:
| • | Driver outside mirror with the automatic day-night feature |
Power and Ground of the Inside Rearview Mirror
| • | With the ignition ON, ignition voltage is supplied to the mirror
from the IGN 3 RR fuse in the rear fuse block. |
| • | Ground for the mirror is provided by G402. |
Inside Rearview Mirror with the Automatic Day-Night Feature System Operation
The inside rearview mirror uses 2 photocell sensors. One sensor is
the headlight sensor, located on the rear side of the mirror. The headlight sensor
is used to determine light conditions present at the mirror face. The other sensor
is the ambient light sensor, located on the front of the mirror or windshield side.
The ambient light sensor is used to determine light conditions present at the mirror.
With automatic day-night feature enabled, the mirror uses ambient light sensor
to determine the exterior light condition. With a low light condition detected, and
a high light condition from behind at the headlight sensor, the inside
rearview mirror will automatically darken the face of the mirror.
In the daytime, the mirror is in a normal state because of the high light
condition that is indicated by the ambient light sensor. With the gear selector
lever in the REVERSE position, backup lamp supply voltage is supplied as an input
to the inside rearview mirror. In night time conditions only, the mirror monitors
this input to disable the automatic day-night feature which allows the face to
gradually change to a normal state. This allows the driver to see objects in the
mirror clearly when backing up.
Driver Outside Rearview Mirror with the Automatic Day-Night Feature
Operation
The inside rearview mirror will also darken the driver outside rearview
mirror. The inside rearview mirror supplies a low reference circuit
and a signal circuit to the driver outside rearview mirror. Refer
to
Outside Mirror Description and Operation
in Doors for further description and
operation of the driver outside rearview mirror.
Compass
The mirror uses two magnetic field sensors for compass direction. One
sensor is for north and south, the other is for east and west. The mirror
supplies a signal and low reference to each sensor. As the vehicle travels
with or against the earth's magnetic pull, there will be a change in voltage
on one or both sensors. As a result of the change in voltage, the mirror
changes the heading on the compass display.
Switches of the Inside Rearview Mirror with the Automatic Day-Night
Feature and Compass without OnStar®
The inside rearview mirror has 2 switches that perform the following
functions:
| • | The MIRROR switch is used to enable or disable the automatic day-night
feature of the mirror. With the ignition in the ON position, depress the
MIRROR switch to enable the automatic day-night feature of
the mirror. A green indicator will illuminate on the mirror when
the automatic day-night feature is enabled. To disable the
automatic day-night feature of the mirror, depress the MIRROR
switch. |
| • | The COMPASS switch is used to turn the compass on and off. With
the ignition in the ON position, depress the COMPASS switch to turn the
compass on. Depress the COMPASS switch again to turn the compass
off. The COMPASS switch is also used to place the compass
into a calibration or zone mode. For more information, refer
to
Compass Calibration and Magnetic Variance
. |
Switches of the Inside Rearview Mirror with the Automatic Day-Night Feature with Compass and OnStar®
The inside rearview mirror has 4 switches that perform the following functions:
| • | The on/off switch located at the left side of the mirror performs the following functions: |
| - | To enable or disable the automatic day-night feature of the mirror. With the ignition in the ON position, depress and hold the on/off switch for 4 seconds to enable the automatic day-night feature of the mirror. A green indicator will illuminate on the mirror when the automatic day-night feature is enabled. To disable the automatic day-night feature of the mirror, depress and hold the on/off switch for 4 seconds. |
| - | To turn the compass on and off. With the ignition in the ON position, depress the on/off switch to turn the compass on. Depress the on/off switch again to turn the compass off. The on/off switch is also used to place the compass into a calibration or zone mode. For more information, refer to
Compass Calibration and Magnetic Variance
. |
| • | The 3 switches on the right side of the mirror are for OnStar® operation. For more information, refer to
OnStar Description and Operation
in Cellular Communication. |
