Circuit Description
The Electronic Suspension Control (ESC) module supplies a 5.0 volt reference signal to the suspension position sensor. The suspension position sensor supplies an analog voltage (0.35-4.75 volts) back to the ESC module which represents the position between the body and the wheel. The sensor is also grounded through the ESC module.
Conditions for Running the DTC
The Ignition is ON.
Conditions for Setting the DTC
| • | The DTC is set when the ESC module measures the position sensor signal voltage below 0.35 volts or above 4.75 volts for more than 1.0 second while the vehicle is operated under normal driving conditions. |
| • | The fault is detected during three consecutive ignition cycles, or during the same ignition cycle after clearing the DTC with a scan tool. |
Action Taken When the DTC Sets
| • | The ESC module will enter the Speed Dependent damping mode. |
| • | Both Left and Right Normal Force outputs will be set to the default output states. |
| • | The SERVICE SUSPENSION SYS message will be displayed. |
Conditions for Clearing the MIL/DTC
| • | The scan tool can be used to clear the DTC. |
| • | The DTC is saved as history when the ESC module no longer sees voltage outside the normal range. The DTC will clear if the fault does not return during 50 consecutive ignition cycles. |
Diagnostic Aids
| • | If this fault condition is set along with DTC C0696, diagnose DTC C0696 first. |
| • | If the DTC is a history DTC, the fault may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Tests for the proper operation of the circuit in the low voltage range.
-
Tests for a short to voltage in the 5 volt reference circuit.
-
Tests for the proper operation of the circuit in the high voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to ground.
-
Tests for a high resistance or an open in the ground circuit.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Suspension Controls Schematics | ||||
1 | Did you perform the Road Sensing Suspension Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Does the scan tool indicate that the position sensor data parameter is within the specified range? | 0.35 - 4.75 V | Go to Diagnostic Aids | Go to Step 3 |
Does the scan tool indicate that the position sensor data parameter is less than the specified value? | 0.35 V | Go to Step 4 | Go to Step 8 | |
Measure the voltage between the 5 volt reference circuit of the position sensor and a good ground. Does the voltage measure near the specified value? | 5 V | Go to Step 5 | Go to Step 6 | |
Does the scan tool indicate that the position sensor data parameter is greater than the specified value? | 4.75 V | Go to Step 7 | Go to Step 9 | |
6 | Does the voltage measure greater than the specified value? | 5.625 V | Go to Step 10 | Go to Step 11 |
Does the voltage measure less than the specified value? | 3.75 V | Go to Step 12 | Go to Step 13 | |
8 | Test the signal circuit of the position sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
9 | Test the signal circuit of the position sensor for a short to ground, high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
10 | Test the 5 volt reference circuit of the position sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
11 | Test the 5 volt reference circuit of the position sensor for a short to ground, high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
12 | Test the low reference circuit of the position sensor for high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
13 | Inspect for poor connections at the harness connector of the position sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 15 |
14 | Inspect for poor connections at the harness connector of the ESC module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 16 |
15 | Replace the position sensor. Refer to Electronic Suspension Front Position Sensor Replacement or Electronic Suspension Rear Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 17 | -- |
16 |
Important: Perform the set up procedure for the ESC module . Replace the ESC module. Refer to Electronic Suspension Control Module Replacement . Did you complete the replacement? | -- | Go to Step 17 | -- |
17 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
