OnStar Microphone Malfuncation Gen. 4
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: OnStar Schematics Connector End View Reference: Cellular Communication Connector End Views DEFINITION: The OnStar® Call Center operator can clearly be heard but the operator is unable to hear the caller. | ||||
1 | Did you perform the Cellular Communication Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Does the OnStar® operator hear your voice? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 |
Does the voltage measure greater than the specified value? | 7 V | Go to Step 4 | Go to Step 5 |
4 | Measure the voltage from the Cellular Microphone Signal circuit to the drain wire. Does the voltage measure greater than the specified value? | 7 V | Go to Step 7 | Go to Step 6 |
5 | Test the Cellular Microphone Signal circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 8 |
6 | Test the drain wire for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
7 | Test the drain wire for a short to ground. Did you find and correct he condition? | -- | Go to Step 13 | Go to Step 10 |
8 |
Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
9 | Inspect for poor connections at the harness connector of the rear view mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
10 | Inspect for poor connections at the harness connector of the Communication Interface Module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
11 | Replace the rear view mirror assembly. Refer to Inside Rearview Mirror Replacement in Stationary Windows. Did you complete the replacement? | -- | Go to Step 13 | -- |
12 |
Important: Perform the OnStar® setup procedure. Replace the VCIM. Refer to Communication Interface Module Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- |
13 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
OnStar Microphone Malfuncation Gen. 5
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: OnStar Schematics Connector End View Reference: Cellular Communication Connector End Views DEFINITION: The OnStar® Call Center operator can clearly be heard but the operator is unable to hear the caller. | ||||
1 | Did you perform the Cellular Communication Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Does the OnStar® operator hear your voice? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 |
Does the voltage measure greater than the specified value? | 9 V | Go to Step 4 | Go to Step 5 |
4 | Measure the voltage from the Cellular Microphone Signal circuit to the drain wire. Does the voltage measure greater than the specified value? | 9 V | Go to Step 7 | Go to Step 6 |
5 | Test the Cellular Microphone Signal circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 8 |
6 | Test the drain wire for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
7 | Test the drain wire for a short to ground. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 10 |
8 |
Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
9 | Inspect for poor connections at the harness connector of the rear view mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
10 | Inspect for poor connections at the harness connector of the Communication Interface Module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
11 | Replace the rear view mirror assembly. Refer to Inside Rearview Mirror Replacement in Stationary Windows. Did you complete the replacement? | -- | Go to Step 13 | -- |
12 |
Important: Perform the OnStar® setup procedure. Replace the VCIM. Refer to Communication Interface Module Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- |
13 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
