GM Service Manual Online
For 1990-2009 cars only

Strut Assembly Replacement FE1, FE3

Removal Procedure

    Notice: Use care when handling the coil springs in order to avoid chipping or scratching the coating. Damage to the coating will result in premature failure of the coil springs.


    Object Number: 402795  Size: SH
  1. Remove the upper strut mounting bolts.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.

  4. Object Number: 105002  Size: SH
  5. Disconnect the wheel speed sensor wiring harness.
  6. Remove the wheel speed sensor bracket from the strut.

  7. Object Number: 420704  Size: SH
  8. Remove the brake line bracket mounting bolt and bracket from the strut.

  9. Object Number: 104991  Size: SH
  10. Remove the strut to steering knuckle bolts and nuts.
  11. Remove the strut from the vehicle.

Installation Procedure

  1. Lower the vehicle.

  2. Object Number: 402795  Size: SH
  3. Install the strut to the vehicle.
  4. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  5. Install the upper strut mounting bolts.
  6. Tighten
    Tighten the upper strut mounting bolts to 40 N·m (30 lb ft).

  7. Raise the vehicle.

  8. Object Number: 104991  Size: SH
  9. Install new strut to steering knuckle bolts and nuts.
  10. Tighten
    Tighten the strut to steering knuckle bolts and nuts to 147 N·m (108 lb ft).


    Object Number: 420704  Size: SH
  11. Install the brake line bracket and mounting bolt to the strut.
  12. Tighten
    Tighten the bolts and nuts to 17 N·m (13 lb ft).

  13. Install the wheel speed sensor bracket and mounting bolt to strut.
  14. Tighten
    Tighten the bolt to 17 N·m (13 lb ft).

  15. Install the wheel speed sensor bracket to strut.
  16. Install the wheel speed sensor wiring harness to the bracket.
  17. Install the wheel and tire. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  18. Lower the vehicle.

Strut Assembly Replacement FE7

Removal Procedure

    Notice: Care should be taken to avoid chipping or scratching the coating when handling the suspension coil spring. Damage to the coating can cause premature failure.


    Object Number: 402795  Size: SH
  1. Remove the 3 strut tower bolts.
  2. Raise the vehicle and suitably support by the frame allowing the control arms to hang free. Refer to Lifting and Jacking the Vehicle .
  3. Remove the wheel and tire. Refer to Tire and Wheel Removal and Installation .

  4. Object Number: 105002  Size: SH
  5. Disconnect the wheel speed sensor connector.
  6. Remove the wheel speed sensor bracket from the dust shield.
  7. Remove the brake line bracket from the strut.

  8. Object Number: 474722  Size: SH
  9. Remove the strut to knuckle bolts.
  10. Remove the strut from the vehicle.

Installation Procedure


    Object Number: 402795  Size: SH
  1. Install the strut.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the 3 strut tower bolts and washers.
  4. Tighten
    Tighten 3 strut tower bolts to 66 N·m (49 lb ft).


    Object Number: 474722  Size: SH
  5. Install the strut to knuckle bolts and nuts.
  6. Tighten
    Tighten the strut to knuckle bolts and nuts to 177 N·m (131 lb ft).

  7. Install the brake line bracket to strut.
  8. Tighten
    Tighten the brake line bracket to 23 N·m (17 lb ft).


    Object Number: 105002  Size: SH
  9. Install the wheel speed sensor bracket to dust shield.
  10. Connect the wheel speed sensor connector.
  11. Install the wheel and tire. Refer to Tire and Wheel Removal and Installation .
  12. Tighten
    Tighten the wheel and tire to 125 N·m (80 lb ft).

  13. Lower the vehicle.