GM Service Manual Online
For 1990-2009 cars only

Front Side Door Trim Panel Replacement Standard

Tools Required

J 36796 Clip Zip Clip Removal Tool, or J 38778 Door Trim Pad Clip Remover

Removal Procedure

  1. Position the window fully downward.

  2. Object Number: 511164  Size: SH
  3. Ensure the manual lock knob (1) is in the unlock position.
  4. Insert a flat bladed tool into the top service notch in order to disengage the locking clip (2) located at the front of the manual lock knob (1).
  5. Remove the manual lock knob (1).

  6. Object Number: 524183  Size: SH
  7. Remove the inside handle bezel from the inner door panel in the following order:
  8. 5.1. Hold the inside handle to the open position.
    5.2. Insert a flat bladed tool at the front lower corner of the bezel.
    5.3. Pry outward on the bezel.
    5.4. Remove the bezel from the inner door panel.
  9. Remove the screw attaching the inside door handle to the sheet metal.

  10. Object Number: 524042  Size: SH
  11. Use the J 36796 or J 38778 in order to release the eight retainers around the outside edges of the door trim panel.
  12. Note the location of the alignment datums (1).


    Object Number: 524044  Size: SH
  13. Slide the door trim panel (1) upwards to release it from the following:
  14. • The alignment datums (4)
    • The eight retainers
    • The arm rest steel retainer clips (3)
    • The inner belt molding (2)
  15. Disconnect the door trim panel electrical connector.

Installation Procedure


    Object Number: 512054  Size: SH
  1. Slide the electrical connector (4) into position on the water deflector (1).
  2. Remove the steel retainer clips (2) from the arm rest pull handle brackets.
  3. Slide the steel clips (2) into the nylon nuts (3).

  4. Object Number: 524044  Size: SH
  5. Install the door trim panel to the inner door in the following order:
  6. 4.1. Position the door trim panel (1) downward over the following:
       • The manual lock rod
       • The inner belt molding (2)
    4.2. Engage the door trim panel simultaneously into the following:
       • The alignment datums (4)
       • The electrical connector
       • The armrest pull handle retainer clips (3)
       • The eight retainers

    Notice: Refer to Fastener Notice in the Preface section.

    Caution: This screw must be properly installed. This screw is critical in order to maintain retention of the inside handle to the slider-glide mechanism. Failure to properly install this screw may allow the door to unlatch during a collision, resulting in personal injury.


    Object Number: 524183  Size: SH
  7. Install the screw attaching the inside door handle to the sheet metal.
  8. Tighten
    Tighten the screw to 0.5 N·m (4 lb in).

  9. Install the inside handle bezel to the inner door panel in the following order:
  10. 6.1. Hold the inside handle to the open position.
    6.2. Insert the rear hook on the bezel to the wood trim tab.
    6.3. Press the forward end of the bezel inward until it is fully seated.

    Object Number: 512057  Size: SH

    Important: Ensure the manual lock rod is in the full up/unlocked position.

  11. Position the manual lock knob (1) into the bezel opening until the locking clip (2) bottoms out on the bezel.
  12. Engage the locking clip (2) located at the front of the lock knob (1) to the lock rod.

Front Side Door Trim Panel Replacement WC2, WC8

Tools Required

    • J 36796 Clip Zip Clip Removal Tool
    • J 38778 Door Trim Pad Clip Remover

Removal Procedure


    Object Number: 511164  Size: SH

    Important: Do NOT scratch the window on the armored vehicle.

  1. Ensure the manual lock knob (1) is in the unlock position.
  2. Insert a flat bladed tool into the top service notch in order to disengage the locking clip (2) located at the front of the manual lock knob (1).
  3. Remove the manual lock knob (1).

  4. Object Number: 524183  Size: SH
  5. Remove the inside handle bezel from the inner door panel in the following order:
  6. 4.1. Hold the inside handle to the open position.
    4.2. Insert a flat bladed tool at the front lower corner of the bezel.
    4.3. Pry outward on the bezel.
    4.4. Remove the bezel from the inner door panel.
  7. Remove the screw attaching the inside door handle to the sheet metal.

  8. Object Number: 524042  Size: SH
  9. Use the J 36796 or J 38778 in order to release the eight retainers around the outside edges of the door trim panel.
  10. Note the location of the alignment datums (1).


    Object Number: 524044  Size: SH
  11. Slide the door trim panel (1) upwards to release the panel from the following components:
  12. • The alignment datums (4)
    • The 8 retainers
    • The arm rest steel retainer clips (3)
    • The inner belt molding (2)
  13. Disconnect the door trim panel electrical connector.

Installation Procedure


    Object Number: 512054  Size: SH
  1. Slide the electrical connector (4) into position on the water deflector (1).
  2. Remove the steel retainer clips (2) from the arm rest pull handle brackets.
  3. Slide the steel clips (2) into the nylon nuts (3).

  4. Object Number: 524044  Size: SH
  5. Install the door trim panel to the inner door in the following order:
  6. 4.1. Position the door trim panel (1) downward over the following:
       • The manual lock rod
       • The inner belt molding (2)
    4.2. Engage the door trim panel simultaneously into the following:
       • The alignment datums (4)
       • The electrical connector
       • The armrest pull handle retainer clips (3)
       • The eight retainers

    Notice: Refer to Fastener Notice in the Preface section.

    Caution: This screw must be properly installed. This screw is critical in order to maintain retention of the inside handle to the slider-glide mechanism. Failure to properly install this screw may allow the door to unlatch during a collision, resulting in personal injury.


    Object Number: 524183  Size: SH
  7. Install the screw attaching the inside door handle to the sheet metal.
  8. Tighten
    Tighten the screw to 0.5 N·m (4 lb in).

  9. Install the inside handle bezel to the inner door panel in the following order:
  10. 6.1. Hold the inside handle to the open position.
    6.2. Insert the rear hook on the bezel to the wood trim tab.
    6.3. Press the forward end of the bezel inward until the bezel is fully seated.

    Object Number: 512057  Size: SH

    Important: Ensure the manual lock rod is in the full up/unlocked position.

  11. Position the manual lock knob (1) into the bezel opening until the locking clip (2) bottoms out on the bezel.
  12. Engage the locking clip (2) located at the front of the lock knob (1) to the lock rod.