GM Service Manual Online
For 1990-2009 cars only

Step

Action

Yes

No

Schematic Reference: Interior Lights Schematics

Connector End View Reference: Lighting Systems Connector End Views or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Open and close all of the doors.
  2. Place the courtesy lamp switch in the OFF position.
  3. Turn ON the ignition, with the engine OFF.

Do the courtesy lamps remain illuminated?

Go to Step 3

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

With a scan tool, observe all of the Door Jamb Switch parameters in each of the Door Module inputs data lists.

Does the scan tool indicate that any of the Door Jamb Switch parameters are ON?

Go to Step 6

Go to Step 4

4

With a scan tool, observe the Interior Lamp Switch parameter in the Instrument Panel Integration Module (IPM) Non - HVAC data list.

Does the scan tool display ON?

Go to Step 5

Go to Step 9

5

  1. Turn OFF the ignition.
  2. Disconnect the headlamp switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Interior Lamp Switch parameter.

Does the scan tool display ON?

Go to Step 8

Go to Step 12

6

  1. Turn OFF the ignition.
  2. Disconnect the appropriate door lock actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Door Jamb Switch parameter.

Does the scan tool display ON?

Go to Step 7

Go to Step 10

7

Test the appropriate door open switch signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 11

8

Test the interior lamp switch on signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 14

9

Test for a short to ground in the appropriate interior lamp control circuit. Refer to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 13

10

Inspect for poor connections at the harness connector of the appropriate door lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 15

11

Inspect for poor connections at the harness connector of the appropriate door module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 16

12

Inspect for poor connections at the harness connector of the headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 17

13

Inspect for poor connections at the harness connector of the rear integration module (RIM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 18

14

Inspect for poor connections at the harness connector of the IPM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 20

Go to Step 19

15

Replace the appropriate door lock actuator. Refer to Front Side Door Latch Replacement and Rear Side Door Latch Replacement in Doors.

Did you complete the replacement?

Go to Step 20

--

16

Replace the appropriate door module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 20

--

17

Replace the headlamp switch. Refer to Headlamp Switch Replacement .

Did you complete the replacement?

Go to Step 20

--

18

Replace the RIM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 20

--

19

Replace the IPM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 20

--

20

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2