GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2005 🢒 DeVille 🢒 Restraints 🢒 SIR 🢒 Instrument Panel Inflatable Restraint Module Replacement

Removal Procedure

    Caution: Refer to SIR Caution in the Preface section.

    Caution: Refer to SIR Inflator Module Handling and Storage Caution in the Preface section.

    Caution: A deployed dual stage inflator module will look the same whether one or both stages were used. Always assume a deployed dual stage inflator module has an active stage 2. Improper handling or servicing can activate the inflator module and cause personal injury.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling .

    2. Object Number: 464940 Size: SH
  2. Remove the right insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gages and Console.
  3. Remove the connector position assurance (CPA) (4) from the instrument panel (I/P) module connector (2).
  4. Remove the I/P module yellow connector (2) from the vehicle wiring harness yellow connector (1).
  5. Remove the I/P module yellow connector (2) from the I/P bracket (3).

    6. Object Number: 464929 Size: SH
  6. Remove the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gages and Console.
  7. Note the routing position of the I/P module wire harness, to help in re-assembly.
  8. Push the I/P module yellow connector (2) back away from the I/P (3).

    9. Object Number: 427782 Size: SH
  9. Remove the I/P module mounting fasteners (2).
  10. Remove the I/P module (3) from the I/P (1).
  11. When removing the I/P module (3) do not damage pigtail and the connector (4).

Installation Procedure

    Object Number: 427782 Size: SH
  1. When installing the I/P module (3) do not damage the pigtail and the connector (4).
  2. Route the I/P module pigtail (4) down through the I/P (1).
  3. Install the I/P module (3) to the I/P (1).

    4. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the mounting fasteners (2) to the inflatable restraint I/P module.

    5. Tighten
    Tighten fasteners to 22 N·m (16 lb ft).


    Object Number: 464929 Size: SH
  5. Route the I/P module wiring harness (2) in place to secure the yellow connector clip to the I/P (3).
  6. Install the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gages and Console.

    7. Object Number: 464940 Size: SH
  7. Clip the I/P module yellow connector (2) to the I/P bracket (3).
  8. Install the I/P module yellow connector (2) to the vehicle harness yellow connector (1).
  9. Install the CPA (4) to the I/P module connector (2).
  10. Install the right insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gages and Console.
  11. Enable the SIR system. Refer to SIR Disabling and Enabling .
  12. Fully deploy the module before disposal. If the module was replaced under warranty, fully deploy and dispose of the module after the required retention period. Refer to Inflator Module Handling and Scrapping .