GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2001 🢒 Eldorado 🢒 Engine 🢒 Engine Controls - 4.6L 🢒 DTC P0741

Object Number: 25443 Size: SF
Master Electrical Component List
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice

Circuit Description

The PCM controls the torque converter clutch (TCC) solenoid valve pulse width modulation (PWM). The solenoid controls the hydraulic fluid for TCC apply and release. When the TCC is applied, the engine is coupled directly to the transmission through the TCC. The TCC slip speed should be near 0.

If the PCM detects high torque converter slip when the TCC is commanded ON, then DTC P0741 sets. DTC P0741 is a type B DTC.

Conditions for Running the DTC
    • No TP DTCs P0121, P0122 or P0123.
    • No VSS DTCs P0502 or P0503.
    • No AT ISS DTCs P0716 or P0717.
    • No TCC stuck ON DTC P0742.
    • No IMS DTCs P1820, P1822, P1823 or P1825.
    • No TCC PWM solenoid valve DTC P1860.
    • The engine run time is greater than 5 seconds.
    • The time since the gear select lever change is greater than 6 seconds.
    • The IMS indicates D2, D3 or D4.
    • The transmission gear ratio indicates 2nd, 3rd or 4th gear.
    • The transmission fluid temperature is 20-133°C (68-271°F).
    • The TP angle is 10-50%.
    • The engine torque is 43-215 N·m (32-159 lb ft).
    • The TCC solenoid valve is commanded ON.

Conditions for Setting the DTC

TCC slip speed exceeds its limit for a given torque for 5 seconds.

Refer to Torque Converter Clutch Slip Speed .

Action Taken When the DTC Sets
    • The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.
    • The PCM inhibits 4th gear if the transmission is in hot mode.
    • The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.
    • The PCM stores DTC P0741 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC
    • The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
    • A scan tool can clear the MIL/DTC.
    • The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.
    • The PCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
    • Inspect the transmission fluid level.
    • The transmission may be in hot mode. Inspect the transmission fluid lines to the radiator. The lines may be pinched, plugged or twisted.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step inspects the transmission fluid to ensure that it is at the proper level.

    2.

  2. This step verifies that the TCC engages when commanded ON by the scan tool.

DTC P0741 TCC System Stuck Off

Step

Action

Value(s)

Yes

No

1

Did you perform the Powertrain Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Did you perform the Transmission Fluid Checking Procedure?

--

Go to Step 3

Go to Transmission Fluid Check

3

  1. Install a Scan Tool .
  2. Turn ON the ignition, with the engine OFF.

    3. Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM.

  3. Record the DTC Freeze Frame and Failure Records.
  4. Clear the DTC.
  5. Drive the vehicle at 72 km/h (45 mph).
  6. Using the Scan Tool , command the TCC PWM solenoid valve ON.
  7. Operate the vehicle under the following conditions:
    8. • The transmission fluid temperature (TFT) is 20-133°C (68-271°F).
    • The engine torque is 43-215 N·m (32-159 lb ft).
    • Drive the vehicle in D4 with a throttle position (TP) angle of 10-50 %.
    • Ensure that the TCC applies for more than 5 seconds.
  8. Monitor the TCC slip speed.

During TCC application, is the slip speed within the specified parameters?

-20 to +100 RPM

Go to Diagnostic Aids

Go to Step 4

4
  1. During TCC apply, if NO change in TCC slip speed, inspect for the following conditions:
    2. • The TCC control valve is stuck OFF due to sediment or binding.
    • The TCC regulator valve is stuck OFF due to sediment or binding.
    • The TCC feed valve is stuck OFF due to sediment or binding.
    • The TCC enable valve is stuck OFF due to sediment or binding.
  2. During TCC apply, if SOME change in TCC slip speed, inspect for the following conditions:
    3. • The TCC PWM oil pressure screen is clogged.
    • The TCC PWM solenoid valve O-ring is leaking or cut.
    • The turbine shaft seal, case cover to turbine shaft seal, case cover to drive sprocket seal and drive sprocket support are worn.
  3. Repair any of the above items as necessary.
  4. If no problems found in previous conditions, replace the T/C viscous clutch.

Refer to Transmission Overhaul in Transmission Unit Repair Manual.

Did you complete the repair?

--

Go to Step 5

--

5

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    4. • The TFT is 20-133°C (68-271°F).
    • The engine torque is 43-215 N·m (32-159 lb ft).
    • Drive the vehicle in D4 with a TP angle of 10-50%.
    • Ensure that the TCC applies and the slip speed is -20 to +100 RPM for 4 seconds.
  4. Select Specific DTC.
  5. Enter DTC P0741.

Has the test run and passed?

--

System OK

Go to Step 1