Circuit Description
The Continuously Variable Road Sensing Suspension (CVRSS) module monitors a lift/dive signal at the Powertrain Control Module (PCM). Under normal conditions, the CVRSS module supplies a 5 volt reference voltage to the PCM. The PCM grounds this circuit when the vehicle is accelerating rapidly or braking hard. When the lift/dive signal goes low to approximately 0 volts, the CVRSS module commands all four CVRSS dampers to a FIRM condition.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
| • | The DTC is set if the CVRSS module does not detect the low-to-high transition on the lift/dive circuit within 31 seconds after the ignition is turned ON. |
| • | The fault is detected during three consecutive ignition cycles, or during the same ignition cycle after clearing the DTC with a scan tool. |
Action Taken When the DTC Sets
| • | The CVRSS lift/dive function will be disabled. |
| • | The vehicle will pitch more during a braking or wide open throttle condition. |
| • | The SERVICE RIDE SYS message will be displayed. |
Conditions for Clearing the MIL/DTC
| • | The scan tool can be used to clear the DTC. |
| • | The DTC is saved as history when the CVRSS module sees the low-to-high transition on the lift/dive signal from the PCM during a valid test period. The DTC will clear if the fault does not return after 50 consecutive ignition cycles. |
Diagnostic Aids
As part of the vehicle diagnostic system, the PCM toggles the lift/dive line within 31 seconds after the ignition is turned ON. This allows the CVRSS module to determine if the line is faulted or not. A retry is attempted every four minutes until successful.
An intermittent short to ground or an open in the Lift/Dive Signal circuit may cause a random firm/soft ride condition.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for proper voltage in the chassis pitch signal circuit.
-
This step tests for proper communication between the PCM and the CVRSS module.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Suspension Controls Schematics | ||||
1 | Did you perform the Road Sensing Suspension Diagnostic System Check? | -- | Go to Step 2 | |
Measure the voltage by backprobing from the chassis pitch signal circuit of the CVRSS module to a good ground. Does the voltage measure near the specified value? | 5 V | Go to Step 3 | Go to Step 4 | |
Does the voltage momentarily drop near the specified value within 31 seconds? | 1 V | Go to Diagnostic Aids | Go to Step 5 | |
4 | Does the voltage measure near the specified value? | B+ | Go to Step 8 | Go to Step 6 |
5 | Test the chassis pitch signal circuit for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 7 |
6 | Inspect for poor connections at the harness connector of the CVRSS module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 9 |
7 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 10 |
8 | Repair the short to voltage in the chassis pitch signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 11 | -- |
9 |
Important: Perform the set up procedure for the CVRSS module. Replace the CVRSS module. Refer to Electronic Suspension Control Module Replacement . Did you complete the replacement? | -- | Go to Step 11 | -- |
10 | Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 4.6L. Did you complete the replacement? | -- | Go to Step 11 | -- |
11 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
