Radio Speaker Amplifier Replacement Base

1. Lower the glove box.
2. Disconnect the electrical connectors.
3. Use the following steps in order to remove the amplifier from the bracket:

3.1.	Push the retention clip upward and in.

3.2.	Rotate the amplifier.

3.3.	Push the amplifier up in order to clear the amplifier mounting bracket and the HVAC module.

3.4.	Remove the amplifier.

1. Connect the amplifier to the bracket by clipping the amplifier into place.
2. Connect the electrical connectors.
3. Inspect the system operation.

Radio Speaker Amplifier Replacement Denali Yukon

1. Remove the rear quarter panel. Refer to Rear Quarter Trim Panel Replacement - Right Side , or to Rear Quarter Trim Panel Replacement - Left Side in Interior Trim.



2. Remove the four amplifier retaining bolts (1).
3. Disconnect the electrical connector.
4. Remove the amplifier from the vehicle.

1. Install the amplifier to the subwoofer.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the amplifier retaining screws (1).

Tighten
Tighten the screws to 2.5 N·m (22 lb in).

3. Connect the electrical connector.
4. Install the rear quarter panel. Refer to Rear Quarter Trim Panel Replacement - Right Side , or to Rear Quarter Trim Panel Replacement - Left Side in Interior Trim.

Radio Speaker Amplifier Replacement Denali Suburban

1. Remove the rear quarter panel. Refer to Rear Quarter Trim Panel Replacement - Right Side , or to Rear Quarter Trim Panel Replacement - Left Side in Interior Trim.



2. Remove the amplifier retaining bolts (2).
3. Disconnect the electrical connector (1).
4. Remove the amplifier from the vehicle.

1. Install the amplifier to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the amplifier retaining bolts (2).

Tighten
Tighten the screws to 9.0 N·m (80 lb in)

3. Connect the electrical connector (1).
4. Install the rear quarter panel. Refer to Rear Quarter Trim Panel Replacement - Right Side , or to Rear Quarter Trim Panel Replacement - Left Side in Interior Trim.

Radio Speaker Amplifier Replacement Escalade EXT

1. Remove the floor console bezels. Refer to Floor Console Bezel Replacement in Instrument Panel, Gages and Console.
2. Remove the console bin. Refer to Front Floor Console Compartment Replacement in Instrument Panel, Gages and Console.



3. Remove the 4 amplifier retaining screws (1).
4. Disconnect the amplifier wire connector from the amplifier.
5. Remove the top bracket.
6. Lift the amplifier from the console bracket.



7. Remove and discard the four pushnuts (1).

1. Install 4 new pushnuts (1).
2. Place the amplifier on the console bracket.
3. Install the top bracket.
4. Connect the wire connector to the amplifier.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the 4 retaining screws.

Tighten
Tighten the 4 retaining screws to 3.4 N·m (30 lb in).

6. Install the console bin. Refer to Front Floor Console Compartment Replacement in Instrument Panel, Gages and Console.
7. Install the floor console bezels. Refer to Floor Console Bezel Replacement in Instrument Panel, Gages and Console.