The rear view camera image display module receives a 12-volt signal from the body control module (BCM) indicating that the vehicle is in reverse gear. When this signal is detected the rear view camera image display module will provide a regulated 6-volt power source to the rear view camera. The rear view image will then be displayed on the radio.

If a proper video signal is not detected, the radio will display a SERVICE REQUIRED notification on the radio display.

A poor video image can be caused by ice, snow, and mud buildup on the lens of the rear view camera. Also, extreme lighting conditions can affect performance, such as operating in the dark or with bright sunlight shining on the camera. Extreme high or low temperatures can also affect the image quality. For normal operating characteristics of the rear vision camera system, refer to the Navigation System section of the owners manual.

Schematic Reference

Object Detection Schematics

Connector End View Reference

Object Detection Connector End Views

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

1. Inspect the rearview camera and verify there are no debris on the lens or that the bezel or bezel seal is not damaged.

⇒	If debris are found on the lens, clean the lens. If the lens, bezel, or bezel seal are damaged, replace as necessary.

2. Ignition ON, vehicle in PARK, verify the backup lamps are off.

⇒	If the backup lamps are illuminated, refer to Rear Vision Camera System Always On.

3. Vehicle in REVERSE, verify a clear rear vision image is displayed on the radio.

⇒	If a clear image is not displayed, refer to Rear Vision Camera System Does Not Display.

Rear Vision Camera System Always On

1. Ignition OFF, disconnect the harness connector at the rear view camera image display module.
2. Ignition ON, vehicle in PARK, verify a test lamp does not illuminate between the control circuit terminal 1 and ground.

⇒	If the test lamp illuminates, test the control circuit for a short to voltage. If the circuit test normal, refer to Backup Lamps Always On.

3. If all circuits test normal, replace the rear view camera image display module.

Rear Vision Camera System Does Not Display

1. Ignition OFF, disconnect the harness connector at the rear view camera image display module.
2. Test for less than 1 ohm between the ground circuit terminal 3 and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

3. Ignition ON, vehicle in PARK, verify that a test lamp illuminates between the ignition circuit terminal 2 and ground.

⇒	If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

4. Ignition ON, park brake applied, transmission in reverse, verify that a test lamp illuminates between the control circuit terminal 1 and ground.

⇒	If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

5. Ignition OFF, connect the harness connector at the rear view camera image display module. Disconnect the harness connector at the rearview camera.
6. Ignition OFF, test for less than 1 ohm between the ground circuit terminal B and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the rear view camera image display module.

7. Ignition ON, vehicle in REVERSE, test for 5.8-6.2 volts between the 6-volt reference circuit terminal A and ground.

⇒	If less than the specified range, test the 6-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the rear view camera image display module.

⇒	If greater than the specified range, test the 6-volt reference circuit for a short to voltage. If the circuit tests normal, replace the rear view camera image display module.

8. Ignition OFF, test for greater than 1 ohm between the camera video signal circuit terminal C and ground.

⇒	If less than the specified range, test the signal circuit for a short to ground.

9. Ignition OFF, disconnect the harness connector at the rear view camera image display module.
10. Test for less then 1 ohm between the shield circuit terminal 10 at the rear vision camera display module harness connector and terminal D at the rear vision camera harness connector.

⇒	If greater than the specified range, test the shield circuit for an open/high resistance.

11. Ignition OFF, disconnect the rearview camera module. Test for less than 1 ohm along the signal circuit terminal C to terminal 9.

⇒	If not the specified value, test the signal circuit for a short to ground.

12. Test for less than 1 volt between the signal circuit terminal 9 and ground.

⇒	If greater than the specified range, test the signal circuit for a short to voltage.

13. Test for less then 1 ohm between the signal circuit terminal 9 at the rear vision camera display module harness connector and terminal C at the rear vision camera harness connector.

⇒	If greater than the specified range, test the signal circuit for an open/high resistance.

14. Ignition OFF, disconnect the X4 harness connector at the radio.
15. Test for less then 1 ohm between the signal circuit terminal 11 at the rear vision camera display module harness connector and terminal 7 at radio harness connector.

⇒	If greater than the specified range, test the signal circuit for an open/high resistance.

16. Test for infinite resistance between the signal circuit terminal 6 at the radio harness connector and ground.

⇒	If not the specified value, test the signal circuit for a short to ground.

17. Test for less than 1 volt between the signal circuit terminal 6 at the radio harness connector and ground.

⇒	If greater than the specified range, test the signal circuit for a short to voltage.

18. Test for less then 1 ohm between the signal circuit terminal 12 at the rear vision camera display module harness connector and terminal 6 at the radio harness connector.

⇒	If greater than the specified range, test the signal circuit for an open/high resistance.

19. If all circuits test normal, test or replace the rear vision camera.
20. Ignition ON, vehicle in REVERSE, verify a clear rear vision image is displayed on the radio.

⇒	If a clear rear vision image is not displayed, replace the radio.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.