DTC B2425 or B2430 Front Seat
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B2425 04: Left Seat Heater Cushion Circuit OpenDTC B2425 0A: Left Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2425 0B: Left Seat Heater Cushion Circuit Current Above Threshold
DTC B2425 0C: Left Seat Heater Cushion Circuit Current Below Threshold
DTC B2425 0D: Left Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2425 0E: Left Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2425 1F: Left Seat Heater Cushion Circuit Intermittent
DTC B2430 04: Right Seat Heater Cushion Circuit Open
DTC B2430 0A: Right Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2430 0B: Right Seat Heater Cushion Circuit Current Above Threshold
DTC B2430 0C: Right Seat Heater Cushion Circuit Current Below Threshold
DTC B2430 0D: Right Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2430 0E: Right Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2430 1F: Right Seat Heater Cushion Circuit Intermittent
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ MSM Terminal 5 C3 | 1, 2, B1935 0C, B1935 0D, B2180 0C, B2180 0D, B2425 0C, B2425 0D, B2430 0C, B2430 0D | 1, 2, B1935 0C, B1935 0D, B2180 0C, B2180 0D, B2425 0C, B2425 0D, B2430 0C, B2430 0D | -- | -- |
Driver Heated Seat Back Element Supply Voltage | B2508 02 | B1935 0C, B1935 0D | B2345 00, B2508 01 | B1935 0B, B1935 0E |
Driver Heated Seat Back Element Control | B2345 00, B2508 02 | B1935 0C, B1935 0D | B2345 00, B2508 01 | B1935 0B, B1935 0E |
Driver Heated Seat Back Temperature Sensor Signal | B2435 02 | B1935 04, B1935 1F, B2435 0D | B1935 04, B1935 1F, B2435 0D | B1935 0A, B2345 13, B2345 42, B2345 4B |
Driver Heated Seat Back Temperature Sensor Low Reference | -- | B1935 04, B1935 1F, B2435 0D | -- | B2345 13, B2345 42, B2345 4B |
Driver Heated Seat Cushion Element Supply Voltage | B2508 02 | B2425 0C, B2425 0D | B2345 00, B2508 01 | B2425 0B, B2425 0E |
Driver Heated Seat Cushion Element Control | B2345 00, B2508 02 | B2425 0C, B2425 0D | B2345 00, B2508 01 | B2425 0B, B2425 0E |
Driver Heated Seat Cushion Temperature Sensor Signal | B1925 02, B2425 1F | B1925 05, B2425 04, B2425 1F | B1925 05, B2425 04, B2425 1F | B2345 13, B2345 42, B2345 4B, B2425 0A |
Driver Heated Seat Cushion Temperature Sensor Low Reference | -- | B1925 05, B2425 04, B2425 1F | -- | B2345 13, B2345 42, B2345 4B |
Passenger Heated Seat Back Element Supply Voltage | B2508 02 | B2180 0C, B2180 0D | B2345 00, B2508 01 | B2180 0B, B2180 0E |
Passenger Heated Seat Back Element Control | B2345 00, B2508 02 | B2180 0C, B2180 0D | B2345 00, B2508 01 | B2180 0B, B2180 0E |
Passenger Heated Seat Back Temperature Sensor Signal | B2440 02 | B2180 04, B2180 1F, B2440 05 | B2180 04, B2180 1F, B2440 05 | B2180 0A, B2345 13, B2345 42, B2345 4B |
Passenger Heated Seat Back Temperature Sensor Low Reference | -- | B2180 04, B2180 1F, B2440 05 | -- | B2345 13, B2345 42, B2345 4B |
Passenger Heated Seat Cushion Element Supply Voltage | B2508 02 | B2430 0C, B2430 0D | B2345 00, B2508 01 | B2430 0B, B2430 0E |
Passenger Heated Seat Cushion Element Control | B2345 00, B2508 02 | B2430 0C, B2430 0D | B2345 00, B2508 01 | B2430 0B, B2430 0E |
Passenger Heated Seat Cushion Temperature Sensor Signal | B2170 02, B2430 1F | B2430 04, B2430 1F, B2170 05 | B2430 04, B2430 1F, B2170 05 | B2345 13, B2345 42, B2345 4B, B2430 0A |
Passenger Heated Seat Cushion Temperature Sensor Low Reference | -- | B2430 04, B2430 1F, B2170 05 | -- | B2345 13, B2345 42, B2345 4B |
1. Power seat inoperative 2. Heated seat inoperative | ||||
Circuit/System Description
The driver and front passenger heated seats are controlled by the memory seat module (MSM). When active, power is applied to the seat cushion and seat back heater elements through a common voltage supply circuit. The module controls the seat temperature by providing a pulse width modulated (PWM) ground through the heated seat element control circuits to the seat heater elements. The module then monitors the current flow through the heating elements and the of rate change of the temperature sensors to verify correct heated seat operation.
Conditions for Running the DTC
The MSM must be powered.
Conditions for Setting the DTC
B2425 04, B2430 04
The module does not detect a temperature change within 210 seconds.
B2425 0A, B2430 0A
The module detects that the set point temperature has not been reached within 8.5 minutes.
B2425 0B, B2425 0E, B2430 0B, B2430 0E
By measuring output current, the module calculates that the heating element resistance is below the minimum resistance.
B2425 0C, B2425 0D, B2430 0C, B2430 0D
By measuring output current, the module calculates that the heating element resistance is above the maximum resistance.
B2425 1F, B2430 1F
The temperature sensor voltage is erratic or changes suddenly.
Action Taken When the DTC Sets
The heated seat cushion function for the affected seat will be disabled.
Conditions for Clearing the DTC
| • | The current DTC clears when the malfunction is no longer present , and the power mode changes to OFF then back to ACC or RUN. |
| • | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Heated/Cooled Seat Connector End Views
Electrical Information Reference
Scan Tool Reference
Circuit/System Testing
B2425 0A, B2425 0B, B2425 0C, B2425 0D, B2425 0E, B2425 04, or B2425 1F
- Ignition OFF, disconnect the C3 harness connector at the MSM.
- Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 5 and ground.
- Ignition OFF, connect the C3 harness connector at the MSM and disconnect the C1 harness connector at the MSM.
- Test for 3.5-11.5 ohms between the supply voltage circuit terminal 14 and the control circuit terminal 11.
- Disconnect the C2, C5 harness connectors at the MSM.
- Test for 850-300K ohms between the signal circuit terminal 1 C5 and the low reference circuit terminal 3 C2.
- Connect the C1, C2, C5 harness connectors at the MSM.
- Disconnect the harness connector at the seat cushion heater element/temperature sensor.
- Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal C and ground.
- If all circuits test normal, replace the MSM.
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
Important: When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).
| ⇒ | If greater than the specified range, test the supply voltage circuit and the control circuit for an open/high resistance. If the circuits test normal replace the seat cushion heater element. |
| ⇒ | If less than the specified range, test for a short between the supply voltage circuit and the control circuit. If the circuits test normal, replace the seat cushion heater element. |
| ⇒ | If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM. |
| ⇒ | If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the MSM. |
B2430 0A, B2430 0B, B2430 0C, B2430 0D, B2430 0E, B2430 04, or B2430 1F
- Ignition OFF, disconnect the C3 harness connector at the MSM.
- Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 5 and ground.
- Ignition OFF, connect the C3 harness connector at the MSM and disconnect the C1, C4 harness connectors at the MSM.
- Test for 3.5-11.5 ohms between the supply voltage circuit terminal 6 C1 and the control circuit terminal 14 C4.
- Disconnect the C2, C5 harness connectors at the MSM.
- Test for 850-300K ohms between the signal circuit terminal 2 C5 and the low reference circuit terminal 6 C2.
- Connect the C1, C2, C4, C5 harness connectors at the MSM.
- Disconnect the harness connector at the seat cushion heater element/temperature sensor.
- Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal C and ground.
- If all circuits test normal, replace the MSM.
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
Important: When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).
| ⇒ | If greater than the specified range, test the supply voltage circuit and the control circuit for an open/high resistance. If the circuits test normal replace the seat cushion heater element. |
| ⇒ | If less than the specified range, test for a short between the supply voltage circuit and the control circuit. If the circuits test normal, replace the seat cushion heater element. |
| ⇒ | If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM. |
| ⇒ | If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the MSM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for the MSM replacement, setup, and programming |
DTC B2425 or B2430 Rear Seat
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B2425 04: Left Seat Heater Cushion Circuit OpenDTC B2425 0A: Left Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2425 0B: Left Seat Heater Cushion Circuit Current Above Threshold
DTC B2425 0C: Left Seat Heater Cushion Circuit Current Below Threshold
DTC B2425 0D: Left Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2425 0E: Left Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2425 1F: Left Seat Heater Cushion Circuit Intermittent
DTC B2430 04: Right Seat Heater Cushion Circuit Open
DTC B2430 0A: Right Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2430 0B: Right Seat Heater Cushion Circuit Current Above Threshold
DTC B2430 0C: Right Seat Heater Cushion Circuit Current Below Threshold
DTC B2430 0D: Right Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2430 0E: Right Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2430 1F: Right Seat Heater Cushion Circuit Intermittent
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Left Rear Heated Seat Cushion Element Supply Voltage | B2508 02 | B2425 0C, B2425 0D | B2345 00, B2508 01 | B2425 0B, B2425 0E |
Left Rear Heated Seat Cushion Element Control | B2345 00, B2508 02 | B2425 0C, B2425 0D | B2345 00, B2508 01 | B2425 0B, B2425 0E |
Left Rear Heated Seat Cushion Temperature Sensor Signal | B1925 02, B2425 1F | B1925 05, B2425 04, B2425 1F | B1925 05, B2425 04, B2425 1F | B2345 13, B2345 42, B2345 4B, B2425 0A |
Left Rear Heated Seat Cushion Temperature Sensor Low Reference | -- | B1925 05, B2425 04, B2425 1F | -- | B2345 13, B2345 42, B2345 4B |
Right Rear Heated Seat Cushion Element Supply Voltage | B2508 02 | B2430 0C, B2430 0D | B2345 00, B2508 01 | B2430 0B, B2430 0E |
Right Rear Heated Seat Cushion Element Control | B2345 00, B2508 02 | B2430 0C, B2430 0D | B2345 00, B2508 01 | B2430 0B, B2430 0E |
Right Rear Heated Seat Cushion Temperature Sensor Signal | B2170 02, B2430 1F | B2430 04, B2430 1F, B2170 05 | B2430 04, B2430 1F, B2170 05 | B2345 13, B2345 42, B2345 4B, B2430 0A |
Right Rear Heated Seat Cushion Temperature Sensor Low Reference | -- | B2430 04, B2430 1F, B2170 05 | -- | B2345 13, B2345 42, B2345 4B |
Circuit/System Description
When the heated seat function is active, the rear heated seat module (RHSM) supplies battery voltage through the element supply voltage circuit to the seat heater elements. The RHSM controls the seat temperature by providing a pulse width modulated (PWM) ground through the heated seat element control circuit to the seat heater elements. The RHSM then monitors the current flow through the heating element and the temperature sensor rate of change to verify correct operation.
Conditions for Running the DTC
The RHSM must be powered and the heated seat must be enabled.
Conditions for Setting the DTC
B2425 04, B2430 04
The RHSM does not detect a temperature change within 210 seconds.
B2425 0A, B2430 0A
The RHSM detects that the set point temperature has not been reached within 8.5 minutes.
B2425 0B, B2425 0E, B2430 0B, B2430 0E
By measuring output current, the RHSM calculates that the heating element resistance is below the minimum resistance.
B2425 0C, B2445 0D, B2430 0C, B2430 0D
By measuring output current, the RHSM calculates that the heating element resistance is above the maximum resistance.
B2425 1F, B2430 1F
The temperature sensor voltage is erratic or changes suddenly.
Action Taken When the DTC Sets
The heated seat cushion function for the affected seat will be disabled.
Conditions for Clearing the DTC
| • | The current DTC clears when the malfunction is no longer present , and the power mode changes to OFF then back to ACC or RUN. |
| • | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Heated/Cooled Seat Connector End Views
Electrical Information Reference
Scan Tool Reference
Circuit/System Testing
B2425 0A, B2425 0B, B2425 0C, B2425 0D, B2425 0E, B2425 04, or B2425 1F
- Ignition OFF, disconnect the C1 harness connector at the RHSM.
- Test for 2.5-8.5 ohms between control circuit terminal 3 and control circuit terminal 5.
- Disconnect the C2, C4 harness connectors at the RHSM.
- Test for 850-300K ohms between the signal circuit terminal 9 C4 and the low reference circuit terminal 6 C2.
- Connect the C1, C2, C4 harness connectors at the RHSM.
- Disconnect the harness connector at the seat cushion heater element/temperature sensor.
- Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal C and ground.
- If all circuits test normal, replace the RHSM.
Important: When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).
| ⇒ | If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal replace the seat cushion heater element. |
| ⇒ | If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater element. |
| ⇒ | If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the RHSM. |
| ⇒ | If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the RHSM. |
B2430 0A, B2430 0B, B2430 0C, B2430 0D, B2430 0E, B2430 04, or B2430 1F
- Ignition OFF, disconnect the C1 harness connector at the RHSM.
- Test for 3.5- 11.5 ohms between control circuit terminal 6 and control circuit terminal 2.
- Disconnect the C2, C4 harness connectors at the RHSM.
- Test for 850-300K ohms between the signal circuit terminal 20 C4 and the low reference circuit terminal 8 C2.
- Connect the C1, C2, C4 harness connectors at the RHSM.
- Disconnect the harness connector at the seat cushion heater element/temperature sensor.
- Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal C and ground.
- If all circuits test normal, replace the RHSM.
Important: When measuring the resistance, the resistance values are based on the seat being at room temperature of 20°C (68°F).
| ⇒ | If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat cushion heater element. |
| ⇒ | If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater element. |
| ⇒ | If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat cushion heater element/temperature sensor. |
| ⇒ | If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the RHSM. |
| ⇒ | If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the RHSM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for the RHSM replacement, setup, and programming |
