GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2007 🢒 Escalade 🢒 General Information 🢒 General Information 🢒 Drive Pinion Flange/Yoke and/or Oil Seal Replacement

Tools Required
    • J 8614-01 Flange and Pulley Holding Tool
    • J 22388 Pinion Oil Seal Installer - Rear

Removal Procedure

    Important: Observe and mark the positions of all the driveline components, relative to the propeller shaft and the axles, prior to disassembly. These components include the propeller shafts, drive axles, pinion flanges, output shafts, etc. Reassemble all the components in the exact places in which you removed the parts. Follow any specifications, torque values, and any measurements made prior to disassembly.

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Drain the drive axle. Refer to Rear Axle Lubricant Replacement .
  3. Remove the tires and wheels (8.6 inch, 9.5 inch axle). Refer to Tire and Wheel Removal and Installation .
  4. Remove the rear brake calipers (8.6 inch, 9.5 inch axle). Refer to Rear Brake Caliper Replacement .
  5. Remove the brake rotors (8.6 inch, 9.5 inch axle). Refer to Rear Brake Rotor Replacement .

    6. Object Number: 361391 Size: SH
  6. Reference mark the rear propeller shaft (3) to the rear axle pinion yoke (4).
  7. Disconnect the propeller shaft from the axle. Wrap the bearing caps with tape in order to prevent the loss of bearing rollers. Support the propeller shaft as necessary.

    8. Object Number: 661077 Size: SH
  8. Measure the amount of torque required to rotate the pinion. Use an inch-pound torque wrench. Record this measurement for reassembly. This will give the combined preload for the following components:
    9. • The pinion bearings
    • The pinion oil seal
    • The differential case bearings
    • The axle bearing (8.6 inch, 9.5 inch axles)

    Object Number: 788905 Size: SH
  9. Place an alignment mark between the pinion and the pinion yoke.

    10. Object Number: 661080 Size: SH
  10. Install the J 8614-01 as shown.
  11. Remove the pinion nut while holding the J 8614-01 .
  12. Remove the washer.

    13. Object Number: 661074 Size: SH
  13. Install the J 8614-2 (2) and J 8614-3 (3) into the J 8614-01 (1) as shown.
  14. Remove the pinion yoke by turning the J 8614-3 (3) clockwise in order to retrieve the lubricant.
  15. Remove the pinion oil seal. Use a suitable seal removal tool.

Installation Procedure

    Object Number: 651744 Size: SH
  1. Install a new pinion oil seal using the J 22388 .
  2. Apply sealant, GM P/N 12346004 (Canadian P/N 10953480) or equivalent, to the splines of the pinion yoke.
  3. Install the pinion yoke. Align the marks made during removal.

    4. Notice: Refer to Pinion Flange/Yoke Installation Notice in the Preface section.

  4. Seat the pinion yoke onto the pinion shaft by tapping it with a soft faced hammer until a few pinion shaft threads show through the yoke.
  5. Install the washer and a new pinion nut.

    6. Object Number: 661080 Size: SH
  6. Install the J 8614-01 onto the pinion yoke as shown.

    7. Notice: Refer to Fastener Notice in the Preface section.

    Important: If the rotating torque is exceeded, the pinion will have to be removed and a new collapsible spacer installed.

  7. Tighten the pinion nut while holding the J 8614-01 .

    8. Tighten
    Tighten the nut until the pinion end play is just taken up. Rotate the pinion while tightening the nut to seat the bearings.


    Object Number: 661077 Size: SH
  8. Measure the rotating torque of the pinion. Compare this measurement with the rotating torque recorded during removal.

    9. Tighten
    Tighten the nut in small increments, as needed, until the rotating torque is 0.40-0.57 N·m (3-5 lb in) greater than the rotating torque recorded during removal.

  9. Once the specified torque is obtained, rotate the pinion several times to ensure the bearings have seated. Recheck the rotating torque and adjust if necessary.

    10. Object Number: 361391 Size: SH
  10. Install the propeller shaft (3) to the pinion yoke (4). Align the reference marks made during removal.
  11. Install the propeller shaft yoke retaining clamp bolts.

    12. Tighten
    Tighten the propeller shaft yoke retaining clamp bolts to 25 N·m (18 lb ft).

  12. Install the brake rotors (8.6 inch, 9.5 inch axles). Refer to Rear Brake Rotor Replacement .
  13. Install the brake calipers (8.6 inch, 9.5 inch axles). Refer to Rear Brake Caliper Replacement .
  14. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation .
  15. Fill the drive axle. Refer to Rear Axle Lubricant Replacement .
  16. Inspect and add axle lubricant to the axle housing, if necessary. Refer to Rear Axle Lubricant Level Inspection .
  17. Lower the vehicle.