The exterior lamps control is located on the instrument panel to the left of
the steering wheel.
It controls the following systems:
| • | Instrument Panel Lights |
The exterior lamps control has four positions:
(Off): Turn the control to this position
to turn off the automatic headlamps and daytime running lamps (DRL). Turning the headlamp
control to the off position again will turn the automatic headlamps or DRL back on.
For vehicles first sold in Canada, the off position will only work when
the vehicle is shifted into the PARK (P) position.
AUTO (Automatic): Turn the control to this position to set the
headlamps to automatically turn on at normal brightness, together with the following:
| • | Instrument Panel Lights |
Turn the control to this position
to turn on the parking lamps together with the following:
| • | Instrument Panel Lights |
Turn the control to this position to turn
on the headlamps together with the following lamps listed below.
When
the headlamps are turned on while the vehicle is on, the headlamps will turn off automatically
10 minutes after the ignition is turned off. When the headlamps are turned on while
the vehicle is off, the headlamps will stay on for 10 minutes before automatically
turning off to prevent the battery from being drained. Turn the headlamp control to
off and then back to the headlamp on position to make the headlamps stay on for an
additional 10 minutes.
| • | Instrument Panel Lights |
IntelliBeam® Intelligent High-Beam Headlamp Control System
If your vehicle has this feature, be sure to read this entire section before
using it.
IntelliBeam® is an enhancement to your vehicle's headlamp system. Using
a digital light sensor on your rearview mirror, this system will turn the vehicle's
high-beam headlamps on and off according to surrounding traffic conditions.
The IntelliBeam® system will turn your high-beam headlamps on when it is
dark enough, there is no other traffic present, and the IntelliBeam® system is
enabled.
Turning On and Enabling IntelliBeam®
Press and release the IntelliBeam® button on the inside rear view mirror.
The IntelliBeam® indicator on the mirror will turn on to let you know the system
has been turned on. Once the system has been turned on, it will remain on each time
the vehicle is started. Additionally, the IntelliBeam® system must be enabled.
To enable the IntelliBeam® system, turn the exterior lamp control to AUTO,
with the turn signal/multifunction lever in its neutral position. The High-Beam On
Light will appear on the instrument panel cluster when the high-beams are on. See
Highbeam On Light
.
Driving with IntelliBeam®
IntelliBeam® will only activate your high-beams when driving over 20 mph
(32 km/h).
The high-beam headlamps will remain on, under the automatic control of IntelliBeam®,
until any of the following situations occur:
| • | The system detects an approaching vehicle's headlamps. |
| • | The system detects a preceding vehicle's taillamps. |
| • | The outside light is bright enough that high-beam headlamps are not required. |
| • | The vehicle's speed drops below 15 mph (24 km/h). |
| | When either of these conditions occur, the IntelliBeam®
feature will be disabled and the IntelliBeam® light in the mirror will turn off
until the high-beam stalk is returned to the neutral position. |
| • | If IntelliBeam® was using low-beams prior to this action, the IntelliBeam®
feature will be temporarily disabled until the stalk is returned to the neutral position. |
| • | The exterior lamp control is turned to any setting except AUTO. |
| | When this occurs, IntelliBeam® will be disabled until the control is turned
back to the AUTO position. |
| • | The IntelliBeam® system is turned off at the inside rearview mirror. |
IntelliBeam® may not turn off the high-beams if the system cannot detect
other vehicle's lamps because of any of the following:
| • | The others vehicle's lamp(s) are missing, damaged, obstructed from view
or otherwise undetected. |
| • | The other vehicle's lamp(s) are covered with dirt, snow and/or road spray. |
| • | The other vehicle's lamp(s) cannot be detected due to dense exhaust, smoke,
fog, snow, road spray, mist or other airborne obstructions. |
| • | Your vehicle's windshield is dirty, cracked or obstructed by something
that blocks the view of the IntelliBeam light sensor. |
| • | Your vehicle's windshield is covered with ice, dirt, haze or other obstructions. |
| • | Your vehicle is loaded such that the front end of the vehicle points upward,
causing the IntelliBeam sensor to aim high and not detect headlamps and taillamps. |
| • | You are driving on winding or hilly roads. |
You may need to manually disable or cancel the high-beam headlamps by turning
the low-beam headlamps on, if any of the above conditions exist.
Disabling and Resetting IntelliBeam® at the Rearview Mirror
IntelliBeam® can be disabled by using the controls on the inside rearview
mirror.
AUTO
(On/Off): To disable the system,
press this button on the inside rearview mirror. The IntelliBeam® indicator will
turn off and will not come back on until the IntelliBeam® button is pressed again.
(Stalk Disable): When IntelliBeam® has turned on the high-beams,
pull or push the high-beam stalk. This will disable IntelliBeam®. The IntelliBeam®
indicator on the mirror will turn off. To re-enable IntelliBeam®, press the IntelliBeam®
button on the mirror.
A different sensitivity setting is available for dealer diagnostics. This is
done by pushing and holding this button for 20 seconds until the IntelliBeam®
indicator light flashes three times. If you accidentally activate this, the vehicle's
setting will automatically be reset each time the ignition is turned off and then
on again.
Cleaning the IntelliBeam® Light Sensor
The light sensor is located on the inside of the vehicle in front of the inside
rearview mirror.
Clean the light sensor window, periodically, using glass cleaner on a soft cloth.
Gently wipe the sensor window. Do not spray glass cleaner directly on the surface
of the sensor window.
