GM Service Manual Online
For 1990-2009 cars only
Makes šŸ¢’ Cadillac šŸ¢’ 2008 šŸ¢’ Escalade šŸ¢’ Engine šŸ¢’ Engine Mechanical - 4.8L, 5.3L, 6.0L, 6.2L, or 7.0L šŸ¢’ Valve Stem Oil Seal and Valve Spring Replacement

Tools Required

    ā€¢ J 22794 Spark Plug Port Adapter
    ā€¢ J 38606 Valve Spring Compressor

Removal Procedure

    Object Number: 343699 Size: SH
  1. Remove the rocker arm. Refer to Valve Rocker Arm and Push Rod Replacement .
  2. Disconnect the spark plug wire at the spark plug.
    3. ā€¢ Twist each plug wire boot 1/2 turn.
    ā€¢ Pull only on the boot in order to remove the wire from the spark plug.

    Object Number: 14824 Size: SH

    Important: Remove the spark plugs from the cylinder head with the engine at room temperature.

  3. Loosen the spark plug 1 or 2 turns.
  4. Brush or air blast away any dirt or debris from around the spark plug.
  5. Remove the spark plug.

    6. Object Number: 310140 Size: SH
  6. Install the J 22794 into the spark plug hole.
  7. Attach an air hose to the J 22794 .
  8. Apply compressed air to the J 22794 in order to hold the valves in place.

    9. Object Number: 218211 Size: SH
  9. Use the J 38606 in order to compress the valve spring.

    10. Object Number: 1559870 Size: SH
  10. Remove the valve stem keys (225).
  11. Carefully release the valve spring tension.
  12. Remove the J 38606 .
  13. Remove the valve spring cap (224).
  14. Remove the valve spring (223).
  15. Remove the valve stem oil seal (222).
  16. Remove the valve (228).

Installation Procedure

    Object Number: 1559870 Size: SH
  1. Clean the cylinder head valve spring seat area.
  2. Lubricate the valve guide and valve stem oil seal with clean engine oil.
  3. Install the valves (228) into the proper port.
  4. Install the valve stem oil seal (222).
  5. Install the valve spring (223).
  6. Install the valve spring cap (224).

    7. Object Number: 218211 Size: SH
  7. Compress the valve spring using the J 38606 .
  8. Install the valve keys.
    9. ā€¢ Use grease in order to hold the valve keys in place.
    ā€¢ Make sure the keys seat properly in the groove of the valve stem.
    ā€¢ Carefully release the valve spring pressure, making sure the valve keys stay in place.
    ā€¢ Remove the J 38606 .
    ā€¢ Tap the end of the valve stem with a plastic faced hammer to seat the keys, if necessary.

    Object Number: 65039 Size: SH
  9. Remove the J 22794 from the spark plug port.

    10. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 14824 Size: SH
  10. Hand start the spark plug.

    11. Tighten
    Tighten the spark plug to 15 NĀ·m (11 lb ft).

  11. Install the spark plug wires at the ignition coil.
  12. Install the spark plug wire to the spark plug.
  13. Inspect the wires for proper installation:
    14. ā€¢ Push sideways on each boot in order to check for proper installation.
    ā€¢ Reinstall any loose boot.
  14. Install the rocker arm. Refer to Valve Rocker Arm and Push Rod Replacement .