Radiator Grille Emblem/Nameplate Replacement. Cadillac Escalade ESV 2007

For 1990-2009 cars only

Makes 🢒 Cadillac 🢒 2007 🢒 Escalade ESV 🢒 Body Hardware and Trim 🢒 Exterior Trim 🢒 Radiator Grille Emblem/Nameplate Replacement

Radiator Grille Emblem/Nameplate Replacement GMC

Callout	Component Name
1	Grille Name Plate Assembly (GMC) Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section. Tip The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new name plate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Using the palm of the hand, wet out the name plate to the body side and ensure full adhesion of the name plate is made.

Callout

Component Name

Grille Name Plate Assembly (GMC)

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Tip

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Using the palm of the hand, wet out the name plate to the body side and ensure full adhesion of the name plate is made.

Radiator Grille Emblem/Nameplate Replacement Escalade

Callout	Component Name
Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.
1	Emblem Assembly (Crest) Tip The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new name plate. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Using the palm of the hand, wet out the emblem to the grille and ensure full adhesion of the emblem is made.
2	Emblem Assembly (Wreath) Tip The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new emblem. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Using the palm of the hand, wet out the emblem to the grille and ensure full adhesion of the emblem is made.

Callout

Component Name

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Emblem Assembly (Crest)

Tip

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Using the palm of the hand, wet out the emblem to the grille and ensure full adhesion of the emblem is made.

Emblem Assembly (Wreath)

Tip

The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Using the palm of the hand, wet out the emblem to the grille and ensure full adhesion of the emblem is made.