• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
---|---|---|---|---|
I/P Dimming Voltage Reference | B1395 03, B3600 03 | B1395 03, B2652 00, B3600 03 | B1395 07 | -- |
Courtesy Lamp Voltage Reference | B2615 00, B2615 02 | B2615 00, B2615 04 | B2615 00, B2615 01 | -- |
LED Dimming Voltage Reference | B2610 00, B2610 02 | B2610 00, B2610 04 | B2610 00, B2610 01 | -- |
LED Indicator Dimming Volage Reference | B2625 00 | B2625 00 | B2625 00 | -- |
Dome Lamp Switch Signal | 2 | 2 | 2 | -- |
Left Front Door Open Switch Signal | 3 | 3 | 3 | -- |
Left Rear Door Open Switch Signal | 4 | 4 | 4 | -- |
Right Front Door Open Switch Signal | 3 | 3 | 3 | -- |
Right Rear Door Open Switch Signal | 4 | 4 | 4 | -- |
Stop Lamp Switch Signal | B1395 03, B3600 03 | -- | -- | -- |
Dome/Reading Lamp Control | B2615 00 | B2615 00 | -- | -- |
Dome/Reading Lamp Supply Voltage | 1 | 1 | -- | -- |
Exterior Lamps Illumination Supply Voltage | 5 | 5 | 5 | -- |
Inadvertent Power Control | 5 | 5 | 5 | -- |
I/P Lamps Dimming Control | B2652 00 | B2652 00 | B2652 00 | -- |
Dome/Reading Lamp Low Control - Driver Door | -- | 1 | -- | -- |
Dome/Reading Lamp Low Control - Passenger Door | -- | 1 | -- | -- |
Exterior Lamps Low Reference | -- | 5 | -- | -- |
I/P Dimmer Switch Ground | -- | 2 | -- | -- |
LH Vanity Mirror Courtesy Lamp Ground | -- | 1 | -- | -- |
Overhead Console Courtesy Lamp Ground | -- | 1 | -- | -- |
Rear Dome Lamp Ground | -- | 1 | -- | -- |
RH Vanity Mirror Courtesy Lamp Ground | -- | 1 | -- | -- |
1. Courtesy Lamps Malfunction 2. Dome Lamp Switch Malfunction 3. Door Open Switch Malfunction - Front 4. Door Open Switch Malfunction - Rear 5. Exterior Lamps Malfunction |
When the interior lamps dimming switch is activated, a variable voltage signal is applied through the instrument panel lamps dimmer switch signal circuit to the body control module (BCM). The BCM then applies a variable voltage signal through the LED indicator dimming supply circuit to the components on the circuit.
The ignition is ON.
The BCM receives a ground signal on the LED indicator dimming supply circuit.
The BCM cease attempt to dim or illuminate the LED indicator lamps.
• | The conditions for setting the DTC are no longer present. |
• | A history DTC clears after 100 malfunction-free ignition cycles. |
• | The BCM receives the clear code command from the scan tool. |
Interior Lights Dimming Schematics
Interior Lighting Systems Description and Operation
Control Module References for scan tool information
• | IP multifunction switch X88/Z88 w/UD7/XA7 terminal 8 |
• | IP multifunction switch Z75 w/UD7 terminal 4 |
• | IP multifunction switch Z75 w/XA7 terminal 7 |
• | 4wd mode switch terminal 4 |
⇒ | If the test lamp is always OFF, test the control circuit for an open/high resistance or short to ground. If the circuit tests normal, replace the BCM. |
⇒ | If the test lamp is always bright, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• | Control Module References for BCM replacement, setup, and programming |