GM Service Manual Online
For 1990-2009 cars only

Rear Brake Hose Replacement JD9


Object Number: 1701809  Size: SF

Callout

Component Name

Caution: Refer to Brake Fluid Caution in the Preface section.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Preliminary Procedures

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation .

1

Fitting, Brake Pipe Rear

Notice: Refer to Fastener Notice in the Preface section.

Tighten
25 N·m (18 lb ft)

Tip

    • Remove any dirt or debris from the brake pipe fitting.
    • The mounting bracket for the brake hose is serviced as part of the brake hose assembly and is not serviced separately.
    • Use a backup wrench when removing or installing the brake pipe fitting.
    • Cap the brake pipe fitting to prevent brake fluid loss or contamination.

2

Bolt, Brake Hose to Axle Rear

Tighten
9 N·m (80 lb in)

Tip
Finger tighten mounting bolt before torquing to the specified value.

3

Bracket, Brake Hose to Axle Rear

4

Bolt, Brake Hose to Caliper Rear

Tighten
40 N·m (30 lb ft)

5

Gaskets, Brake Hose to Caliper (Qty: 2)

Tip

    • Make sure the gaskets are not still attached to the brake hose or bolt, if not remove them.
    • DO NOT re-use the gaskets. Install NEW gaskets.

6

Hose, Brake Rear

Tip

    •  When installing the brake hose, DO NOT twist or pinch the brake hose.
    • Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding .

Rear Brake Hose Replacement JH6


Object Number: 1702184  Size: SF

Callout

Component Name

Caution: Refer to Brake Fluid Caution in the Preface section.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Preliminary Procedures

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation .

1

Bolt, Brake Hose to Caliper Rear

Notice: Refer to Fastener Notice in the Preface section.

Tighten
40 N·m (30 lb ft)

2

Gasket, Brake Hose to Caliper (Qty: 2)

Tip
DO NOT re-use the copper gaskets. Install NEW gaskets.

3

Fitting, Brake Pipe Rear

Tighten
25 N·m (18 lb ft)

Tip

    • Remove any dirt or debris fron the brake pipe fitting.
    • Use a backup wrench when removing or installing the brake pipe fitting.
    • Cap the brake pipe fitting to prevent brake fluid loss and contamination.

4

Bolt, Brake Hose Bracket to Rear Axle

Tighten
12 N·m (106 lb in)

5

Hose, Brake Rear

Tip

    • When installing or removing the brake hose, DO NOT bend or twist the brake hose.
    • Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding .

Rear Brake Hose Replacement Frame to Rear Axle JD9


Object Number: 1702264  Size: MF

Callout

Component Name

Caution: Refer to Brake Fluid Caution in the Preface section.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Preliminary Procedure

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

1

Fitting, Brake Pipe Rear (Qty: 2)

Notice: Refer to Fastener Notice in the Preface section.

Tighten
25 N·m (18 lb ft)

Tip

    • Remove any dirt or debris from the brake pipe fitting.
    • Use a backup wrench to hold the brake hose while removing or installing either the brake hose or brake pipe.
    • Cap the brake pipe fitting to prevent brake fluid loss and contamination.

2

Bolt, Brake Hose Bracket to Frame Rear

Tighten
25 N·m (18 lb ft).

3

Bracket, Brake Hose to Frame Rear

4

Fitting, Brake Pipe Rear (Qty: 2)

Tip

    • Remove any dirt or debris from the brake pipe fitting.
    • Use a backup wrench to hold the brake hose while removing or installing either the brake hose or brake pipe.
    • Cap the brake pipe fitting to prevent brake fluid loss and contamination.

Tighten
25 N·m (18 lb ft)

5

Bolt, Brake Hose Bracket to Axle Housing Rear

Tighten
25 N·m (18 lb ft)

6

Hose, Frame to Axle Rear Brake

Tip

    • When installing the brake hose bracket to the axle housing, ensure the brake hose bracket is properly located and properly seated on the rear axle housing mounting bracket.
    • Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding .

7

Bracket, Brake Hose to Rear Axle Housing

Rear Brake Hose Replacement Frame to Rear Axle JH6


Object Number: 1850392  Size: MF

Callout

Component Name

Caution: Refer to Brake Dust Caution in the Preface section.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Preliminary Procedure

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

1

Brake Pipe Fitting (Qty: 2)

Notice: Refer to Fastener Notice in the Preface section.

Procedure

  1. Remove any dirt or debris from the brake pipe fitting.
  2. Cap the brake pipe fitting to prevent brake fluid loss and contamination.

Tighten
25 N·m (18 lb ft)

2

Hose Bracket to Frame Bolt (Qty: 2)

Tighten
25 N·m (18 lb ft)

3

Brake Pipe Fitting (Qty: 2)

Procedure

  1. Remove any dirt or debris from the brake pipe fittings.
  2. Cap the brake pipe fittings to prevent brake fluid loss and contamination.

Tighten
25 N·m (18 lb ft)

4

Hose to Rear Axle Bolt

Tighten
25 N·m (18 lb ft)

5

Rear Brake Hose Assembly

Procedure

Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding .