GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC 1052: PPS Preload Failure Region 1

DTC 1053: PPS Preload Failure Region 2

DTC 1054: PPS Preload Failure Region 3

DTC 1055: PPS Preload Failure Region 4

Circuit/System Description

The passenger presence system (PPS) is divided up into 4 regions. When there is an unwanted force being applied to one or more PPS regions, the PPS will set a diagnostic trouble code (DTC). If the PPS detects any preload DTC within the PPS, the PPS will communicate to the SDM through a non GMLAN communications circuit that a PPS fault is present. The SDM will then set DTC B0081 indicating a problem within the PPS and will suppress the deployment of the instrument panel I/P module and then turn the airbag indicator ON.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC


Object Number: 1573876  Size: SH

The PPS will set a DTC when a region has detected a preload/pressure on it. Refer to chart below for specific region.

DTC

Preload Regions

DTC 1052

Region 1

DTC 1053

Region 2

DTC 1054

Region 3

DTC 1055

Region 4

Action Taken When the DTC Sets

    • The PPS will set a DTC, and then communicate with the SDM via non GMLAN circuit.
    • The SDM will set DTC B0081.
    • The SDM disables the I/P module deployment loop.
    • The PPS will turn ON the passenger air bag status OFF indicator.
    • The SDM commands the AIR BAG indicator ON via serial data communications.

Conditions for Clearing the DTC

    • When conditions for the DTC to set no longer exist, use CLEAR DTC function of the scan tool to clear the DTC.
    • After 255 consecutive warm-up cycles without failure, the DTC will be cleared.

Diagnostic Aids

When passenger seat bottom trim cover is serviced or removed, the trim cover, when reinstalled may apply certain unwanted pressure to the PPS causing DTCs 1052-1055 to set.

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

SIR Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Circuit/System Verification

  1. Use the scan tool. Go to the PPS menu, then retrieve the DTCs.
  2. Verify DTC B1051 does not set.
  3. If DTC 1051 is set as current, refer to DTC 1051 .
  4. Using the chart provided in the Conditions for Setting the DTC, locate the region associated with the DTC that is set.
  5. Important: If preload DTC resets after adjusting the seat bottom trim cover, it may be necessary to perform this procedure again.

  6. Use the scan tool and perform Passenger Presence System Preload Test , and then request codes. Verify that there is no preload DTCs set.
  7. If no preload DTCs are set, then remove the seat bottom trim cover and reinstall. Refer to Inflatable Restraint Passenger Presence System Replacement - Front . After reinstalling refer to Repair Verification.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Refer to Control Module References for PPS replacement, setup and programming.

Repair Verification

Use the scan tool and perform Passenger Presence System Preload Test and then request codes. Verify that any preload DTCs set after trying to adjust the seat bottom trim.

If any preload DTC resets, replace the PPS.