GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Special Tools

J 44394 Seal Protector


    Object Number: 906775  Size: SH
  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  2. Remove the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation.
  3. Important: The wheel drive shaft spindle nut must not be reused. Replace the wheel drive shaft spindle nut with a new nut when ever it is removed.

  4. Insert a drift or punch into the brake rotor and against the caliper in order to prevent the wheel hub and bearing from turning.
  5. Remove and discard the wheel drive shaft spindle nut.
  6. Remove the drift or punch from the rotor.
  7. Remove the rear knuckle assembly. Refer to Knuckle Replacement.

  8. Object Number: 728893  Size: SH
  9. Using a suitable tool, carefully release the wheel drive shaft from the differential enough to install the J 44394 .

  10. Object Number: 814136  Size: SH

    Notice: J-44394 must be installed into the differential output shaft seal prior to removing and installing the wheel drive shaft. Failure to install J-44394 as indicated may cause the splines of the wheel drive shaft to cut the differential output seal.

  11. Carefully install the J 44394 over the wheel drive shaft.
  12. Carefully slide the J 44394 into the differential output shaft seal.
  13. Remove the wheel drive shaft from the vehicle.
  14. Remove and discard the wheel drive shaft retaining ring. The wheel drive shaft retaining ring is on the splined shaft of the inner joint housing.

Installation Procedure


    Object Number: 814135  Size: SH
  1. Install the new wheel drive shaft retaining ring. The wheel drive shaft retaining ring is on the splined shaft of the inner joint housing.
  2. Notice: J-44394 must be installed into the differential output shaft seal prior to removing and installing the wheel drive shaft. Failure to install J-44394 as indicated may cause the splines of the wheel drive shaft to cut the differential output seal.

  3. If previously removed carefully install J 44394 into the differential output shaft seal.

  4. Object Number: 814136  Size: SH

    Important: In order to prevent lubricant leaks, use care when installing the wheel drive shaft to the differential. Do not damage the oil seal. Replace the oil seal if it becomes nicked, distorted, or is otherwise damaged.

  5. Carefully install the wheel drive shaft into the differential until the splines are past the J 44394

  6. Object Number: 814137  Size: SH
  7. Carefully remove the J 44394 from the differential output shaft seal.

  8. Object Number: 814138  Size: SH
  9. Carefully remove J 44394 from the wheel drive shaft.
  10. Carefully install the wheel drive shaft into the differential until the retaining ring is engaged.
  11. Ensure the wheel drive shaft retaining ring is fully engaged to the differential by grasping the inner joint housing and pulling outward. The wheel drive shaft will stay positively engaged if properly installed to the differential.
  12. Install the rear knuckle. Refer to Knuckle Replacement.
  13. Important: Ensure that the drive shaft seals do not have any abrasions, cuts or punctures.

  14. Loosely install the NEW wheel drive shaft spindle nut.

  15. Object Number: 906775  Size: SH
  16. Insert a drift or punch into the brake rotor and against the caliper in order to prevent the wheel hub and bearing from turning.
  17. Notice: Refer to Fastener Notice in the Preface section.

  18. Use the New wheel drive shaft spindle nut to slowly pull the drive shaft to the wheel hub and bearing assembly.
  19. Tighten
    Tighten the wheel drive shaft spindle nut to 160 N·m (118 lb ft).

  20. Remove the drift or punch from the rotor.
  21. Install the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation.
  22. Inspect the differential lubricant level. Refer to Rear Axle Lubricant Level Inspection.
  23. Lower the vehicle.