GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2008 🢒 SLS 🢒 Transmission/Transaxle 🢒 Automatic Transmission - 5L40-E/5L50-E 🢒 Control Valve Body Accumulator Assembly Assemble

Special Tools

    • J 36850 Transjel Lubricant
    • J 39068 Valve Body Guide Pins

    Object Number: 1659089 Size: SH
  1. Install J 39068 onto the front and rear control valve bodies.

    2. Object Number: 1659093 Size: SH

    Important: Ensure the coating of transmission fluid is covering the area where the guide pins are installed.

  2. Using a light coat of transmission fluid on both sides of the spacer plate (307), install NEW gaskets (305, 309) onto the spacer plate.
  3. Install the NEW solenoid valve filter assemblies (308, 312) onto the control valve body spacer plate (307).

    4. Object Number: 1659096 Size: SH
  4. Install the control valve body spacer plate (307) and gaskets (305, 309) as an assembly onto the valve bodies.

    5. Object Number: 801960 Size: SH

    Important: Do not use an excessive amount of J 36850 to retain the checkballs.

  5. Use J 36850 to install the 12 checkballs (306) onto the channel plate (304). Refer to Ball Check Valve Locations .

    6. Object Number: 1659100 Size: SH
  6. Using a light coating of transmission fluid, install a NEW gasket (303) onto the channel plate (304).

    7. Object Number: 1659102 Size: SH

    Important: The manual valve should not turn while aligning channel plate.

  7. Install the control valve body channel plate (304) and gasket (303) as an assembly.
  8. Use J 36850 to install the control valve channel plate check ball spring (302) onto the channel plate (304).
  9. Install the control valve channel plate (301) onto the channel plate gasket (303).

    10. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1659105 Size: SH
  10. Install the control valve body bolts (300) into the valve body.

    11. Tighten
    Tighten the control valve body bolts (300) to 11 N·m (8 lb ft).

  11. Remove the J 39068 from the valve body (47).

    12. Object Number: 801934 Size: SH
  12. Install the direct clutch accumulator piston fluid seal rings (314, 316) onto the direct clutch accumulator piston (315).
  13. Install the direct clutch accumulator piston (315) into the direct clutch accumulator housing (317).

    14. Object Number: 801933 Size: SH
  14. Install the overdrive clutch accumulator piston fluid seal rings (320, 322) onto the overdrive clutch accumulator piston (321).
  15. Install the overdrive accumulator piston (321) into the overdrive clutch accumulator housing (323).

    16. Object Number: 801932 Size: SH
  16. Install the intermediate clutch accumulator fluid seal rings (325, 327) onto the intermediate clutch accumulator piston (326).
  17. Install the intermediate clutch accumulator piston (326) into the intermediate clutch accumulator housing (328).

    18. Object Number: 801930 Size: SH
  18. Install the 2nd clutch accumulator piston fluid seal rings (330, 332) onto the 2nd clutch accumulator piston (331).
  19. Install the 2nd clutch accumulator piston (331) into the 2nd clutch accumulator housing (333).

    20. Object Number: 801965 Size: SH

    Important: Reassemble the accumulators in the position they were before disassembly. Refer to Control Valve Body Accumulator Assembly Disassemble.

  20. Install the direct clutch accumulator spring (313).
  21. Install the direct clutch accumulator housing (317) onto the valve body (47).
  22. Install the direct clutch accumulator housing bolts (318) into the valve body (47).

    23. Tighten
    Tighten the accumulator housing bolts (318) to 11 N·m (8 lb ft).


    Object Number: 801967 Size: SH
  23. Install the overdrive clutch accumulator spring (319).
  24. Install the overdrive clutch accumulator housing (323) onto the valve body.
  25. Install the overdrive clutch accumulator housing bolts (318) into the valve body.

    26. Tighten
    Tighten the accumulator housing bolts (318) to 11 N·m (8 lb ft).


    Object Number: 801969 Size: SH
  26. Install the intermediate clutch accumulator spring (324).
  27. Install the intermediate clutch accumulator housing (328) onto the valve body.
  28. Install the intermediate clutch accumulator housing bolts (318) into the valve body.

    29. Tighten
    Tighten the accumulator housing bolts (318) to 11 N·m (8 lb ft).


    Object Number: 801970 Size: SH
  29. Install the 2nd clutch accumulator spring (329).
  30. Install the 2nd clutch accumulator housing (333) onto the valve body.
  31. Install the 2nd clutch accumulator housing bolts (318) into the valve body.

    32. Tighten
    Tighten the accumulator housing bolts (318) to 11 N·m (8 lb ft).