The 4-5 shift solenoid valve is located in the control valve body of the transmission. The transmission control module (TCM) selects the required gear by turning the appropriate solenoid ON or OFF, enabling the transmission to shift. Refer to Shift Solenoid Valve State and Gear Ratio .
The TCM provides voltage to the solenoid through high side driver 2 (HSD2). The TCM uses a second driver to control the solenoid ground circuit. The controlled ground driver reports feedback voltage to the TCM. When the TCM commands the 4-5 shift solenoid valve ON, the voltage of the control circuit should be approximately 0 volts. When the TCM commands the 4-5 shift solenoid valve OFF, the voltage of the control circuit should be approximately system voltage.
When the TCM detects a continuous open or short to ground in the 4-5 shift solenoid valve circuit, then DTC P0979 sets. DTC P0979 is a type B DTC.
This diagnostic procedure supports the following DTC:
DTC P0979 4-5 Shift Solenoid (SS) Control Circuit Low Voltage
• | Ignition voltage is between 8-18 volts. |
• | The engine speed is between 450-6,800 RPM, for 5 seconds. |
• | HSD2 is commanded ON. |
When the following conditions are present and more than 43 out of 50 samples occur, DTC P0979 may set
• | The TCM detects an open in the 4-5 shift solenoid valve circuit when HSD2 is commanded ON. |
• | The TCM detects a short to ground in the 4-5 shift solenoid valve circuit when HSD2 is commanded OFF. |
• | The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the second consecutive drive trip in which the Conditions for Setting the DTC are met. |
• | The TCM turns off power to all solenoids. |
• | The transmission will operate in fifth gear if the vehicle has successfully completed a 1-2 upshift in the current ignition cycle. If the vehicle has not completed a 1-2 upshift in the current ignition cycle, the transmission will operate in fourth gear. |
• | The TCM commands maximum line pressure. |
• | The TCM freezes transmission adaptive functions. |
• | Torque management is inhibited. |
• | At the time of the first failure, the TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as a Failure Record. |
• | At the time of the second failure, the ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as a Freeze Frame. |
• | The TCM stores DTC P0979 in TCM history. |
• | The ECM turns OFF the MIL after the sixth consecutive drive trip in which the TCM does not send a MIL illumination request. |
• | A scan tool can clear the MIL/clearing DTC. |
• | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring. |
• | The TCM cancels the default actions when the ignition is OFF long enough in order to power down the TCM. |
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||
---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||
Important:
Does the solenoid operate? | -- | Go to Step 9 | Go to Step 3 | |||||
3 |
Does the test lamp illuminate? | -- | Go to Step 4 | Go to Step 7 | ||||
4 |
Refer to Component Resistance . Is the resistance within the specified range? | 15.0-20.3Ω | Go to Step 5 | Go to Step 8 | ||||
5 | Using the DMM, measure the resistance for J 45681 terminal 17 to ground. Is the resistance greater than the specified value? | 50K Ω | Go to Step 6 | Go to Step 8 | ||||
6 |
Refer to Testing for Continuity and Testing for Short to Ground . Did you find a condition? | -- | Go to Step 10 | Go to Step 9 | ||||
7 |
Did you find the condition? | -- | Go to Step 10 | Go to Step 9 | ||||
8 |
Refer to Testing for Continuity and Testing for Short to Ground . Did you find the condition? | -- | Go to Step 11 | Go to Step 12 | ||||
9 | Replace the TCM. Refer to Control Module References . Is the operation complete? | -- | Go to Step 13 | -- | ||||
10 | Perform the necessary wiring repairs. Refer to Circuit Testing and Wiring Repairs . Is the action complete? | -- | Go to Step 13 | -- | ||||
11 | Replace the AT internal transmission wiring harness. Refer to Transmission Internal Electrical Harness Replacement . Is the operation complete? | -- | Go to Step 13 | -- | ||||
12 | Replace the 4-5 shift solenoid valve. Refer to 4-5 Shift Solenoid Valve Replacement . Is the operation complete? | -- | Go to Step 13 | -- | ||||
13 | Perform the following procedures in order to verify the repair:
Has the test run and passed? | -- | Go to Step 14 | Go to Step 2 | ||||
14 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK |