GM Service Manual Online
For 1990-2009 cars only

Use the Scan Tool Data List under the following conditions:

    • The Diagnostic System Check - Vehicle is complete.
    • The on-board diagnostics are functioning properly.
    • No diagnostic trouble codes (DTCs) are present.

The values below represent a typical display recorded from a properly functioning system.

Important: Do not use a scan tool that displays faulty data. Report the condition to the scan tool manufacturer. The use of a faulty scan tool can result in misdiagnosis and the unnecessary replacement of parts

Only the parameters listed below are used in this manual for diagnosing. If a scan tool displays other parameters, the values are not recommended by General Motors for use in diagnosis.

Scan tool values below were recorded under the following conditions:

    • Engine at idle
    • Upper radiator hose hot
    • Closed throttle
    • Transmission in PARK
    • Closed Loop Operation
    • Accessories OFF
    • Brake pedal not applied

Scan Tool Parameter

Data List*

Units Displayed

Typical Data Value

1-2 Shift Time

F0, F2

Seconds

Varies

2-3 Shift Time

F0, F2

Seconds

Varies

3-4 Shift Time

F0, F2

Seconds

Varies

4-5 Shift Time

F0, F2

Seconds

Varies

5-6 Shift Time

F0, F2

Seconds

Varies

TP Calculated

F0, F1, F2

%

Varies

Commanded Gear

F0, F1, F2, F3

1, 2, 3, 4 or 1, 2, 3, 4, 5 or Park/Neutral, Reverse, 1, 2, 3, 4, 5

1, 2, 3, 4, 5, or 6

Driver Shift Control

F0

Active/Inactive

Inactive

Driver Shift Request

F0

Upshift/ Downshift/ None/ Invalid

None

Engine Coolant Temperature

F0, F1, F2

°C(°F)

Varies

Engine Speed

F0, F1, F2

RPM

Varies

Engine Torque

F0, F1, F2

N·m (lb ft)

Varies

Ratio

F0, F1, F2, F3

Ratio

Varies

High Side Driver 2

F1, F2, F3

Enabled/Disabled

Enabled

High Side Driver 2 Circuit Status

F1, F2, F3

OK, Open/Short to Volts, Short to GND, Indeterminate

OK

Ignition Voltage

F0, F2, F3

Volts

12-14

Internal Mode Switch

F0, F2

Park-Drive 1, Open, Invalid

Park

IMS A/B/C/P

F0, F2

HI/LOW

Varies

Input and Output Shaft Speed Sensor Supply Voltage

F0, F1, F2

OK, Out of Range

OK

Last Shift Time

F0, F2

Seconds

Varies

Line PC Solenoid Circuit Status

F3

OK, Open/Short to GND, Short to Volts, Indeterminate

OK

Line PC Solenoid Pressure Command

F0, F3

kPa (psi)

Varies

PC Sol. 2 Circuit Status

F3

OK, Open/Short to GND, Short to Volts, Indeterminate

OK

PC Solenoid 2 Pressure Comm.

F0, F3

kPa (psi)

Varies

PC Sol. 3 Circuit Status

F3

OK, Open/Short to GND, Short to Volts, Indeterminate

OK

PC Solenoid 3 Pressure Comm.

F0, F3

kPa (psi)

Varies

PC Sol. 4 Circuit Status

F3

OK, Open/Short to GND, Short to Volts, Indeterminate

OK

PC Solenoid 4 Pressure Comm.

F0, F3

kPa (psi)

Varies

PC Sol. 5 Circuit Status

F3

OK, Open/Short to GND, Short to Volts, Indeterminate

OK

PC Solenoid 5 Pressure Comm.

F0, F3

kPa (psi)

Varies

PC Sol. 1 Circuit Status

F3

OK, Open/Short to GND, Short to Volts, Indeterminate

OK

Shift Solenoid 1

F0, F2, F3

On/Off

On

Shift Sol.2 Circuit Status

F3

OK, Open/Short to GND, Short to Volts, Indeterminate

OK

Shift Solenoid 2

F0, F2, F3

On/Off

On

TCC Brake Switch (Torque Converter Clutch)

F0, F1, F2

Open/Closed

Open

TCC PC Sol.Pressure Command

F0, F1, F3

kPa (psi)

Varies

TCC Slip Speed (Torque Converter Clutch)

F0, F1, F2

RPM

Varies

The TCM Temperature

F0, F1, F2

°C(°F)

Varies

TFP Switch 1

F0

HI/LOW

HI/LOW

TFP Switch 3

F0

HI/LOW

HI/LOW

TFP Switch 4

F0

HI/LOW

HI/LOW

TFP Switch 5

F0

HI/LOW

HI/LOW

Trans. Fluid Temp.

F0, F1, F2

°C(°F)

Varies

Transmission Input Shaft Speed

F0, F1, F2

RPM

Varies

Transmission Output Shaft Speed

F0, F1, F2

RPM

Varies

*Data List Legend

    • F0: Transmission Data
    • F1: TCC Data
    • F2: Shift Data
    • F3: Solenoid Data