Circuit Description
The heated oxygen sensor (HO2S) heater reduces the time required for the oxygen sensor to reach operating temperature and maintains the operating temperature during extended idle periods. When the ignition is turned to the ON position, ignition voltage is supplied directly to the sensor heater. The engine control module (ECM) controls the heater operation by first modulating the control circuit to ground when the sensors are cold. This prevents the possibility of thermal shock to the sensor, from condensation build-up on the sensor, by controlling the sensor's rate of heating. After a predetermined amount of time, the ECM commands the heaters ON continuously. Once the sensor reaches operating temperature, the ECM may modulate the heater control circuit to ground to maintain a desired temperature.
The ECM controls the heater by grounding the control circuit with a solid state device called a driver. The driver is equipped with a feedback circuit that is pulled up to a voltage. The ECM can determine if a control circuit is open, shorted to ground, or shorted to a voltage by monitoring the feedback voltage. If the ECM detects the control circuit voltage is less than a predetermined value when the circuit is commanded OFF, this DTC sets.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
| • | DTC P0031 HO2S Heater Control Circuit Low Voltage Bank 1 Sensor 1 |
| • | DTC P0037 HO2S Heater Control Circuit Low Voltage Bank 1 Sensor 2 |
| • | DTC P0051 HO2S Heater Control Circuit Low Voltage Bank 2 Sensor 1 |
| • | DTC P0057 HO2S Heater Control Circuit Low Voltage Bank 2 Sensor 2 |
Conditions for Running the DTC
P0031 and P0051
| • | Engine is running. |
| • | The ignition 1 voltage is between 10.5-18 volts. |
| • | The ECM has commanded the heated oxygen sensor (HO2S) heater ON and OFF at least once during the ignition cycle. |
| • | DTC P0031, P0051 run continuously once the above conditions are met. |
P0037 and P0057
| • | The engine speed is more than 80 RPM. |
| • | The ignition 1 voltage is between 10-18 volts. |
| • | Rear HO2S heater is ready. |
| • | Rear HO2S is near to frost state. |
| • | The ECM has commanded the HO2S heater ON and OFF at least once during the ignition cycle. |
| • | DTCs P0037, P0057 run continuously once the above conditions are met. |
Conditions for Setting the DTC
| • | The ECM detects a ground in the heater circuits of the HO2S when the heater is commanded OFF. |
| • | The condition exists for more than 4 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 4 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, last test failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Use the J 35616-A/BT-8637 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector. |
| • | The lower connector of the ECM is connector C1 and the upper connector of the ECM is connector C2. Refer to Front of Vehicle/Engine Compartment Component Views. |
| • | If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the circuit status for the component with a scan tool. The circuit status parameter changes from OK or Indeterminate to Fault if there is a condition with the circuit or a connection. The ODM information is in the output driver module (ODM) data list. |
| • | Inspect the sensor pigtail or the harness for contacting the exhaust system. |
| • | For an intermittent condition, refer to Intermittent Conditions. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
If both DTCs are set for either the front sensors or the rear sensors, the ignition voltage circuit to the heaters may be open. The front sensors are fused separately from the rear sensors.
-
The heater control circuit is equipped with a feedback voltage. This feedback voltage allows the ECM to determine if the heater control circuit is open, shorted to ground, or shorted to a voltage. If the feedback voltage on the control circuit is not within the specified range, there is a condition internal to the ECM.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Component Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does DTC P0031, DTC P0037, DTC P0051, or DTC P0057 fail this ignition? | -- | Go to Step 4 | Go to Step 3 |
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids |
Are DTCs P0031 and P0051 set at the same time or are DTCs P0037 and P0057 set at the same time? | -- | Go to Step 7 | Go to Step 5 | |
Note: The ignition must be OFF when disconnecting or connecting the heated oxygen sensor (HO2S) electrical connector. Is the voltage within the specified range? | 4.6-5.2 V | Go to Step 8 | Go to Step 6 | |
6 |
Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
7 |
Note: The ignition voltage circuit supplies voltage to other components. Make sure you test all circuits for a short to ground or test all components for being shorted that share the ignition voltage circuit. Did you complete the repairs? | -- | Go to Step 10 | -- |
8 | Replace the HO2S. Refer to the appropriate procedure: Did you complete the replacement? | -- | Go to Step 10 | -- |
9 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 11 |
11 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
