Circuit Description
The transmission control module (TCM) controls the torque converter clutch (TCC) pulse width modulation (PWM) solenoid valve. The solenoid directs the hydraulic fluid for TCC apply and release. When the TCC is applied, the engine is coupled directly to
the transmission through the TCC. The TCC slip speed should be near 0.
If the TCM detects high torque converter slip when the TCC is commanded ON, then DTC P0741 sets. DTC P0741 is a type B DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0741 Torque Converter Clutch (TCC) System - Stuck Off
Conditions for Running the DTC
• | The ignition voltage is between 8-18 volts. |
• | The engine speed is between 450 and 6,800 RPM for at least 5 seconds. |
• | No IMS DTCs P1815, P1820, P1822, P1823, P1825 or P1826. |
• | No TP sensor DTC P1791, P1795. |
• | Engine torque default values are not being used. |
• | No ISS DTCs P0716 or P0717. |
• | No OSS DTCs P0722 or P0723. |
• | The IMS range is D2, D3, D4, or D5. |
• | No TCC solenoid electrical DTCs P1866 or P1867. |
• | No TCC stuck ON DTC P0742. |
• | The elapsed time since the most recent range change is greater than 6 seconds. |
• | The TP angle is between 10 and 90 percent. |
• | The TFT is 20-130°C (68-266°F). |
• | The engine torque is greater than 55 N·m (41-334 lb ft). |
• | The gear ratio is within the following ranges: |
- | 1.56:1 to 1.64:1 - 3rd gear |
- | 0.98:1 to 1.03:1 - 4th gear |
- | 0.73:1 to 0.77:1 - 5th gear |
• | The TCC Commanded Pressure is greater than 200 kPa (29 psi) for more than 2 seconds. |
• | The TCC duty cycle is greater than 80 percent for more than 2 seconds. |
Conditions for Setting the DTC
The TCM commands the TCC ON twice, and the TCC slip is between 150-250 RPM for greater than 5 seconds.
Action Taken When the DTC Sets
• | The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the second consecutive drive trip in which the Conditions for Setting the DTC are met. |
• | The TCM inhibits 5th gear if the transmission is in Hot Mode. |
• | The TCM commands maximum line pressure. |
• | The TCM freezes transmission adaptive functions. |
• | At the time of the first failure, the TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as a Failure Record. |
• | At the time of the second failure, the ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as a Freeze Frame. |
• | The TCM stores DTC P0741 in TCM history. |
Conditions for Clearing the DTC
• | The ECM turns OFF the MIL after the sixth consecutive drive trip in which the TCM does not send a MIL illumination request. |
• | A scan tool can clear the DTC. |
• | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without a non emission related diagnostic fault occurring. |
• | The TCM cancels the DTC default actions when the ignition is OFF long enough in order to power down the TCM. |
Diagnostic Aids
Inspect the transmission fluid lines to the radiator. The lines may be pinched, plugged or twisted.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step inspects the transmission fluid to ensure that it is at the proper level.
-
This step verifies that the TCC engages when commanded ON by the scan tool.
Step
| Action
| Value(s)
| Yes
| No
|
1
| Did you perform the Diagnostic System Check - Vehicle?
| --
| Go to
Step 2
| Go to
Diagnostic System Check - Vehicle
|
2
| Perform the Transmission Fluid Checking Procedure. Refer to
Transmission Fluid Check
.
Did you perform the Transmission Fluid Checking Procedure?
| --
| Go to
Step 3
| Go to
Transmission Fluid Check
|
3
|
- Install a scan tool.
- Turn ON the ignition, with the engine OFF.
Important:
• | Before clearing the DTC, use the scan tool in order to record the ECM Freeze Frame and the TCM Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the ECM and the TCM. |
• | Using the Clear Info function erases stored DTCs in both the ECM and TCM. |
- Record the DTC Freeze Frame and Failure Records.
- Clear the DTC.
- Operate the vehicle in D at 72 km/h (45 mph).
- Using the scan tool, command the TCC PWM solenoid valve ON.
- Monitor the TCC slip speed on the scan tool.
Is the slip speed within the specified range?
| -20 to +75 RPM
| Go to
Testing for Intermittent Conditions and Poor Connections
| Go to
Step 4
|
4
|
• | Inspect the front control valve body assembly (311) for the following conditions: |
- | TCC PWM solenoid valve (352) mechanically stuck off or leaking |
• | Inspect the fluid pump assembly (202) for the following conditions: |
- | TCC control valve (235) stuck in the off position |
Did you find and correct any of the above conditions?
| --
| Go to
Step 5
| --
|
5
| Perform the following procedure in order to verify the repair:
- Select DTC.
- Select Clear Info.
- Operate the vehicle under the following conditions:
• | The TFT is 20-130°C (68-266°F). |
• | The engine torque is greater than 55-450 N·m (41-334 lb ft). |
• | Drive the vehicle in D with the throttle position at 12-90 percent. |
• | Ensure that the TCC applies and the slip speed is -20 to +75 RPM for 4 seconds. |
- Select Specific DTC.
- Enter DTC P0741.
Has the test run and passed?
| --
| Go to
Step 6
| Go to
Step 2
|
6
| With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?
| --
| Go to
Diagnostic Trouble Code (DTC) List - Vehicle
| System OK
|