Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P0969: Clutch Pressure Control (PC) Solenoid 3 System PerformanceDTC P0970: Clutch Pressure Control (PC) Solenoid 3 Control Circuit Low Voltage
DTC P0971: Clutch Pressure Control (PC) Solenoid 3 Control Circuit High Voltage
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Clutch PC Solenoid 3 Control | P0970 | P0971 | P0971 | P0969 |
Clutch PC Solenoid 3 High Side Driver 2 | P1833 | P1833 | P1834 | P0969 |
Typical Scan Tool Data
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Clutch PC 3 Sol. CKT Status | Operational | Open/Short to Voltage | Short to Ground | Open/Short to Voltage |
High Side Driver 2 CKT Status | Operational | Open/Short to GND | Open/Short to GND | Short to Voltage |
Circuit/System Description
The clutch pressure control (PC) solenoid 3 is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The TCM supplies 12 volts to the clutch PC solenoid 3 on the high side driver 2 circuit. The TCM control the clutch PC solenoid 3 through the clutch PC solenoid 3 control circuit. The normally high clutch PC solenoid 3 flows fluid to the low and reverse clutch and the 4-5-6 clutch. The clutch PC solenoid 3 regulates the transmission fluid pressure to the low and reverse clutch and 4-5-6 clutch assemblies.
Conditions for Running the DTC
P0969
Start the ignition switch, run the engine.
P0970
| • | DTC P0970 is not set. |
| • | Start the ignition switch, run the engine. |
Conditions for Setting the DTC
P0969
The TCM detects an internal electrical performance malfunction of the clutch PC solenoid control circuit and the actual low and reverse/4-5-6 clutch pressure does not equal the commanded low and reverse/4-5-6 clutch pressure for 4.4 seconds in the 5 seconds sample time.
P0970
The TCM detects an internal low voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds in the 375 milliseconds sample time.
P0971
The TCM detects an internal high voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds in the 375 milliseconds sample time.
Action Taken When the DTC Sets
| • | DTC P0969 is a type C DTC. |
| • | DTCs P0970 and P0971 are a type A DTC. |
| • | The TCM defaults the transmission to a limited shift pattern, 2 forward gears and reverse, based on the fault detected. |
| • | The TCM commands maximum line pressure. |
| • | The TCM freezes transmission adaptive functions. |
Conditions for Clearing the DTC
| • | DTC P0969 is a type C DTC. |
| • | DTC P0970 and P0971 is a type A DTC. |
Diagnostic Aids
When attempting to set DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test DTCs.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics
Connector End View Reference
DTC Type Reference
Electrical Information Reference
Circuit Verification
Perform the following procedure to place the control solenoid (w/body and TCM) valve assembly under the optimal conditions to test solenoid electrical DTCs.
| • | Ensure the transmission fluid temperature is between 50-80°C (122-176°F). |
| • | Operate the vehicle in second gear long enough to ensure at least a 3°C (5°F) rise in TCM substrate temperature and then operate the vehicle in fourth gear for 5 seconds. |
Component Testing
The scan tool data parameter Clutch PC 3 Sol. CKT Status normally displays OK.
| ⇒ | If the parameter displays Open/Short to Volts or Short to GND or if the DTC resets, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection and if no concerns are found, replace the control solenoid (w/body and TCM) valve assembly. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for TCM replacement, setup, and programming |
