The body control system consists of the following 2 modules:

Each of the 2 body control modules integrate a number of functional systems. Each module is connected to the class 2 serial data circuit, many of the control signals are implemented by class 2 messages.

The various dash integration module (DIM) input and output circuits are described in the corresponding functional areas as indicated on the DIM electrical schematics.

The DIM functions include the following:

The DIM is the power mode master (PMM). Refer to Power Mode Description and Operation for more information.

The power management function is designed to monitor the vehicle electrical load and determine when the battery is potentially in a high discharge condition. This is accomplished by using a high accuracy battery voltage reading as an indicator of battery discharge rate. The following 6 levels of load management will execute in the load management control algorithm when there is a high discharge condition:

1. The first action requests a vehicle idle speed increase to the engine control module (ECM) in order to raise alternator output.
2. The second action requests a greater vehicle idle speed increase to the ECM in order to raise alternator output.
3. The third action begins to shed vehicle loads in an attempt to remedy the heavy discharge condition.
4. The fourth action requests another vehicle idle speed increase to the ECM in order to raise further the alternator output.
5. The fifth action begins to shed further vehicle loads in an attempt to remedy the heavy discharge condition.
6. If the above 5 corrective actions fail, the sixth action of power management further sheds loads in a final attempt to remedy the high discharge condition.

Loads subject to reduction include the following:

The power mode master (PMM) calculates the battery temperature, voltage and charging rate at all times while the engine is running. The PMM calculates the battery temperature by factoring in:

If the battery temperature is below set limits, the PMM institutes steps to control the load.

The PMM calculates the voltage of the battery by making constant measurements and using the measurements to calculate the true battery voltage. If the PMM detects a low voltage, the PMM institutes steps to control the load.

The PMM calculates the discharge rate, or draw, on the battery by making constant measurements and using the measurements to calculate the discharge rate in amp/hours. If the PMM detects a high current draw from the battery, the PMM institutes steps to control the load.

The PMM will either request an increase in the engine idle speed to the ECM or the PMM will cycle or turn OFF loads, called the load-shed function, in order to preserve the vehicle electrical system operation. The criteria used by the PMM to regulate this electrical load management are outlined below:

Each load management function, either idle boost or load-shed, is discrete. No 2 functions are implemented at the same time.

During each load management function, the PMM checks the battery temperature, battery voltage and amp-hour calculations and determines if the PMM should implement a different power management function.

Idle Boost Functions

The PMM sends a serial data request to the ECM to increase the idle speed. The ECM then adjusts the idle speed by using a special program and idle speed ramp calculations in order to prevent driveability and safety concerns. The idle speed boost and cancel function will vary from vehicle to vehicle and from one moment to another on the same vehicle. This happens because the ECM responds to changes in the inputs from the sensors used to control the powertrain.

Load Shed Function

The PMM executes the load shed function, by controlling the relay coil of the following devices.

The dash integration module (DIM) is able to control or perform all of the DIM functions in the wake-up state. The DIM enters the sleep state when active control or monitoring of system functions has stopped, and the DIM has become idle again. The DIM must detect certain wake-up inputs before entering the wake-up state. The DIM monitors for these inputs during the sleep state, where the DIM is able to detect switch transitions that cause the DIM to wake-up when activated or deactivated. Multiple switch inputs are needed in order to sense both the insertion of the ignition key and the power mode requested. This would allow the DIM to enter a sleep state when the key is IN or OUT of the ignition.

The DIM will enter a wake-up state if any of the following wake-up inputs are detected:

The DIM will enter a sleep state when all of the following conditions exist:

If all these conditions are met, the DIM will enter a low power or sleep condition. This condition indicates that the DIM, which is the power mode master (PMM) of the vehicle, has sent an OFF-ASLEEP message to the other systems on the serial data line.

The various rear integration module (RIM) inputs and outputs are described in the corresponding functional areas as indicated on the RIM electrical schematics.

The RIM functions include the following: