GM Service Manual Online
For 1990-2009 cars only

Diagnostic Aids

The engine may overheat due to an intermittent operation of one of the following components:

    • The after boil heater pump
    • The coolant bypass solenoid
    • The coolant bypass valve
    • The mechanical cooling fan
    • The electric cooling fans
    • The thermostat

For electrical inspection of the cooling fans and the after boil heater pump, refer to Testing for Intermittent Conditions and Poor Connections .

Step

Action

Value(s)

Yes

No

DEFINITION: Engine temperature lamp comes ON and stays ON, or the temperature gage shows hot, or coolant overflows from the surge tank onto the ground while the engine is running.

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Inspect the surge tank for low coolant.

Is there a loss of coolant?

--

Go to Loss of Coolant

Go to Step 3

3

Important: Do not allow the engine temperature to exceed the specified value.

Start the engine and allow to reach normal operating temperature.

Does the engine begin to exceed the specified value?

107°C (225°F)

Go to Step 4

Go to Diagnostic Aids

4

  1. Inspect for loose, damaged, and/or missing of the following:
  2. • The A/C condenser seals
    • The front air deflector
    • The side seals
  3. Repair the system as necessary.

Does the engine still overheat?

--

Go to Step 5

Go to Step 18

5

Using the J 23688 Coolant and Battery Fluid Tester, test for insufficient coolant concentration.

Is the coolant protection greater than the specified value?

-37°C (-34°F)

Go to Step 6

Go to Step 7

6

Correct the coolant concentration as necessary.

Does the engine still overheat?

--

Go to Step 7

Go to Step 18

7

Inspect for obstructed radiator air flow or bent radiator fins.

Is the radiator air flow obstructed?

--

Go to Step 8

Go to Step 9

8

Clean the radiator. Refer to Radiator Cleaning .

Does the engine still overheat?

--

Go to Step 9

Go to Step 18

9

Inspect the drive belt tensioner. Refer to Drive Belt Tensioner Diagnosis for the 3.6L engine or Drive Belt Tensioner Diagnosis for the 4.6L engine.

Is the drive belt tensioner working properly and is the tension correct?

--

Go to Step 11

Go to Step 10

10

Replace the drive belt tensioner. Refer to Water Pump and Generator Belt Tensioner Replacement or Air Conditioning Compressor and Power Steering Pump Belt Tensioner Replacement for the 3.6L engine or Drive Belt Tensioner Replacement - Generator or Drive Belt Tensioner Replacement - Air Conditioning, Power Steering, and Water Pump for the 4.6L engine.

Does the engine still overheat?

--

Go to Step 11

Go to Step 18

11

Inspect the thermostat for proper operation. Refer to Thermostat Diagnosis .

Does the thermostat operate properly?

--

Go to Step 13

Go to Step 12

12

Replace the thermostat. Refer to Engine Coolant Thermostat Replacement .

Does the engine still overheat?

--

Go to Step 13

Go to Step 18

13

Inspect for an inoperative after boil coolant pump if equipped.

Does the engine still overheat?

--

Go to Step 14

Go to Step 18

14

Inspect for an inoperative cooling fan. Refer to Cooling Fan Inoperative .

Does the engine still overheat?

--

Go to Step 15

Go to Step 18

15

Inspect for blocked cooling system passages.

Are the cooling system passages blocked?

--

Go to Step 16

Go to Step 17

16

Replace the radiator. Refer to Radiator Replacement .

Does the engine still overheat?

--

Go to Step 17

Go to Step 18

17

Replace the engine water pump. Refer to Water Pump Replacement .

Did you complete the repair?

--

Go to Step 18

--

18

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 2