GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B1735 01: Seat Front Up Switch Circuit Short to Battery

DTC B1740 01: Seat Front Down Switch Circuit Short to Battery

DTC B1745 01: Seat Rear Up Switch Circuit Short to Battery

DTC B1750 01: Seat Rear Down Switch Circuit Short to Battery

DTC B1755 01: Seat Assembly Forward Switch Circuit Short to Battery

DTC B1760 01: Seat Assembly Rearward Switch Circuit Short to Battery

DTC B1815 01: Seat Recline Forward Switch Circuit Short to Battery

DTC B1820 01: Seat Recline Rearward Switch Circuit Short to Battery

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Front Vertical Up Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

Front Vertical Down Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

Rear Vertical Up Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

Rear Vertical Down Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

Horizontal Forward Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

Horizontal Rearward Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

Recline Forward Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

Recline Rearward Switch Signal

2

1

B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01

--

1. Power seat inoperative

2. Scan Tool Does Not Communicate With Low Speed GMLAN Device

Circuit/System Description

When the power seat switches are pressed, they send a 12-volt signal through the switch signal circuits to the memory seat module (MSM). The MSM then commands the driver seat and lumbar motors to move in response to the switch signals.

Conditions for Running the DTC

The MSM must be powered.

Conditions for Setting the DTC

    • If a seat switch circuit is active in one direction and the switch for the opposite direction is pressed, this DTC will set.
    • Multiple DTCs will set if one of the switch signal circuits is shorted to voltage.

Action Taken When the DTC Sets

    • A motor output driven in response to a switch considered failed, is deactivated for both directions.
    • All memory recall commands are ignored.
    • The MSM will respond to any other switch signal that has not set a DTC.

Conditions for Clearing the DTC

    • The current DTC will clear and set the code to history, 3 seconds after the fault is no longer present and the ignition is cycled OFF then back to ACC or RUN.
    • The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.

Diagnostic Aids

If one of the switch signal circuits is shorted to battery, multiple codes will set.

Reference Information

Schematic Reference

Driver Seat Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Power Seats System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References

Circuit/System Verification

Ignition ON, observe all scan tool Memory Seat Module seat switch parameters while pressing and releasing each seat directional switch. The reading should change between Inactive and Active.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
  2. Verify the scan tool seat switch parameters listed below are Inactive.
  3. • Front Vertical Upward Switch
    • Front Vertical Downward Switch
    • Rear Vertical Upward Switch
    • Rear Vertical Downward Switch
    • Horizontal Forward Switch
    • Horizontal Rearward Switch
    • Recline Forward Switch
    • Recline Rearward Switch
    If not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the MSM.
    • Front vertical upward switch terminal M (LHD) or terminal H (RHD)
    • Front vertical downward switch terminal L (LHD) or terminal G (LHD)
    • Rear vertical upward switch terminal K
    • Rear vertical downward switch terminal J
    • Horizontal forward switch terminal E (LHD) or terminal C (RHD)
    • Horizontal rearward switch terminal D (LHD) or terminal B (RHD)
    • Recline forward switch terminal B (LHD) or terminal F (RHD)
    • Recline rearward switch terminal A (LHD) or terminal E (RHD)
  4. If all circuits test normal, test or replace the seat adjuster switch.

Component Testing

  1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
  2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal F (LHD) or terminal A (RHD) with the switch in the open position.
  3. • Front vertical upward switch terminal M (LHD) or terminal H (RHD)
    • Front vertical downward switch terminal L (LHD) or terminal G (LHD)
    • Rear vertical upward switch terminal K
    • Rear vertical downward switch terminal J
    • Horizontal forward switch terminal E (LHD) or terminal C (RHD)
    • Horizontal rearward switch terminal D (LHD) or terminal B (RHD)
    • Recline forward switch terminal B (LHD) or terminal F (RHD)
    • Recline rearward switch terminal A (LHD) or terminal E (RHD)
    If not the specified value, replace the seat adjuster switch.
  4. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal F (LHD) or terminal A (RHD) with the switch in the closed position.
  5. • Front vertical upward switch terminal M (LHD) or terminal H (RHD)
    • Front vertical downward switch terminal L (LHD) or terminal G (LHD)
    • Rear vertical upward switch terminal K
    • Rear vertical downward switch terminal J
    • Horizontal forward switch terminal E (LHD) or terminal C (RHD)
    • Horizontal rearward switch terminal D (LHD) or terminal B (RHD)
    • Recline forward switch terminal B (LHD) or terminal F (RHD)
    • Recline rearward switch terminal A (LHD) or terminal E (RHD)
    If greater than the specified range, replace the seat adjuster switch.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Power Seat Switch Replacement
    •  Control Module References for MSM replacement, setup, and programming