GM Service Manual Online
For 1990-2009 cars only

Description

This repair procedure gives you the option of using an installation procedure for either metal-inert gas (MIG) welding or adhesive bonding. The choice of installation depends on the type of application requirements. The adhesive bonding procedure may also require MIG welding in some areas of the repair.

Removal Procedure

Caution: Refer to Approved Equipment for Collision Repair Caution in the Preface section.

Important: Before beginning the repair, refer to Metal Panel Bonding for proper adhesive preparations and general information.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling .
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

  3. Object Number: 1222984  Size: SH
  4. Remove all related panels and components.
  5. Repair as much of the damage as possible to factory specifications. Refer to Dimensions - Body .
  6. Caution: Refer to Foam Sound Deadeners Caution in the Preface section.

  7. Note the location and remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair .
  8. Remove the windshield. Refer to Windshield Replacement .

  9. Object Number: 1223028  Size: SH
  10. Locate and drill out all factory welds. Note the number and location of welds for installation of the roof panel.

  11. Object Number: 1222903  Size: SH
  12. With an assistant remove the roof panel.

Installation Procedure (Metal-Inert Gas (MIG) Welding)


    Object Number: 858976  Size: SH
  1. If you are MIG welding the roof panel, perform the following steps:
  2. 1.1.  Drill 8 mm (5/16 in) plug weld holes as necessary in locations noted from the original panel.

            Important: If the location of the original plug weld holes can not be determined, or if structural weld-thru adhesive is present, space the plug weld holes every 40 mm (1½ in) apart.

    1.2. Prepare all mating surfaces, as necessary.
    1.3. Apply 3M® Weld-Thru coating P/N 05916, or equivalent, to all mating surfaces.

    Object Number: 1222903  Size: SH
  3. With the aid of an assistant, position the roof panel to the body.

  4. Object Number: 1223087  Size: SH
  5. Plug weld accordingly.
  6. Clean and prepare all welded surfaces.
  7. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair .
  8. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems .
  9. Install the windshield. Refer to Windshield Replacement .
  10. Install all related panels and components.
  11. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  12. Enable the SIR system. Refer to SIR Disabling and Enabling .

Installation Procedure (Adhesive Bonding)

  1. Grind the surface of the body mating flanges to bare steel.

  2. Object Number: 873290  Size: SH
  3. Grind the roof panel mating flanges to remove the E-coating. Take care not to damage the corners or thin the metal during the grinding operation.
  4. Clean the mating surfaces.
  5. Important: The adhesive has a 40 to 50 minute working time. Do not allow the adhesive to totally cure off the vehicle, as proper alignment of the roof panel to the body will be difficult.


    Object Number: 873291  Size: SH
  6. Apply a 3-6 mm (1/8-¼ in) bead of metal panel bonding adhesive GM P/N 12378566/7 (Canadian P/N 88901674/5) or equivalent, to both of the mating surfaces.

  7. Object Number: 873295  Size: SH
  8. Using a small acid brush, spread a coat of adhesive to cover all the bare metal surfaces to ensure corrosion protection.

  9. Object Number: 1222903  Size: SH

    Important: DO NOT pull the panels apart after joined together. Slide the panels against each other to realign the panels.

  10. Install the roof panel to the body with 2 or more assistants.

  11. Object Number: 1224764  Size: SH
  12. Clamp the roof panel into position, as required.
  13. Using lacquer thinner remove the excess adhesive from the roof panel area.
  14. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair .
  15. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems .
  16. Install the windshield. Refer to Windshield Replacement .
  17. Install all related panels and components.
  18. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  19. Enable the SIR system. Refer to SIR Disabling and Enabling .