Table 1: | Remote Control Door Lock Receiver Scan Tool Data Parameters |
Table 2: | Remote Control Lock Receiver Scan Tool Output Controls |
Parameter | Expected Value | Definition |
---|---|---|
Operating Conditions: Ignition ON | ||
Fob 1 Battery | OK | The scan tool displays OK or Low. This is the state of the Fob 1 battery. |
Fob 1 Function | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 1 command as monitored by the RCDLR. |
Fob 1 Programmed | Yes | The scan tool displays Yes or No. Yes is displayed if the Fob 1 is programmed into the RCDLR. |
Fob 2 Battery | OK | The scan tool displays OK or Low. This is the state of the Fob 2 battery. |
Fob 2 Function | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 2 command as monitored by the RCDLR. |
Fob 2 Programmed | Yes | The scan tool displays Yes or No. Yes is displayed if the Fob 2 is programmed into the RCDLR. |
Fob 3 Battery | OK | The scan tool displays OK or Low. This is the state of the Fob 3 battery. |
Fob 3 Function | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 3 command as monitored by the RCDLR. |
Fob 3 Programmed | Yes | The scan tool displays Yes or No. Yes is displayed if the Fob 3 is programmed into the RCDLR. |
Fob 4 Battery | OK | The scan tool displays OK or Low. This is the state of the Fob 4 battery. |
Fob 4 Function | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 4 command as monitored by the RCDLR. |
Fob 4 Programmed | Yes | The scan tool displays Yes or No. Yes is displayed if the Fob 4 is programmed into the RCDLR. |
Front Placard | Varies | This displays Counts. |
Last Fob Used | Varies | The scan tool displays None, Fob 1, Fob 2, Fob 3, Fob 4 or Fob 5. This was the last Fob used, as monitored by the RCDLR. |
Learn in Progress | Yes | The scan tool displays Yes or No. This is the status of the key fob. |
LF Pressure Sensor Mode | Varies | The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the left front pressure sensor. |
LF Pressure Status | Normal | The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the left front tire pressure. |
LF Tire Press. Sensor Status | Normal | The scan tool displays Normal or Failed. This is the state of the left front tire pressure sensor. |
LF Tire Pressure | Varies | This displays kPa (psi). This is the amount of pressure in the left front tire. |
LF Tire Pressure Sensor Battery Status | OK | The scan tool displays OK or Low. This is the state of the battery in the left front tire pressure sensor. |
LR Pressure Sensor Mode | Varies | The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the left rear pressure sensor. |
LR Pressure Status | Normal | The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the left rear tire pressure. |
LR Tire Press. Sensor Status | Normal | The scan tool displays Normal or Failed. This is the state of the left rear tire pressure sensor. |
LR Tire Pressure | Varies | This displays kPa (psi). This is the amount of pressure in the left rear tire. |
LR Tire Pressure Sensor Battery Status | OK | The scan tool displays OK or Low. This is the state of the battery in the left rear tire pressure sensor. |
Rear Placard | Varies | This displays Counts. |
RF Pressure Sensor Mode | Varies | The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the right front pressure sensor. |
RF Pressure Status | Normal | The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the right front tire pressure. |
RF Tire Press. Sensor Status | Normal | The scan tool displays Normal or Failed. This is the state of the right front tire pressure sensor. |
RF Tire Pressure | Varies | This displays kPa (psi). This is the amount of pressure in the right front tire. |
RF Tire Pressure Sensor Battery Status | OK | The scan tool displays OK or Low. This is the state of the battery in the right front tire pressure sensor. |
RR Pressure Sensor Mode | Varies | The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the right rear pressure sensor. |
RR Pressure Status | Normal | The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the right rear tire pressure. |
RR Tire Press. Sensor Status | Normal | The scan tool displays Normal or Failed. This is the state of the right rear tire pressure sensor. |
RR Tire Pressure | Varies | This displays kPa (psi). This is the amount of pressure in the right rear tire. |
RR Tire Pressure Sensor Battery Status | OK | The scan tool displays OK or Low. This is the state of the battery in the right rear tire pressure sensor. |
Selected Front Tire Type | Varies | The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of front tires used on the vehicle. |
Selected Rear Tire Type | Varies | The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of rear tires used on the vehicle. |
TPM Indicator/Message | Off | The scan tool displays On or Off. This is the state of the TPM indicator. |
TPM System Enabled | Yes | The scan tool displays Yes or No. Yes is displayed if the TPM system is enabled. |
Scan Tool Output Control | Description |
---|---|
Copy and Paste TPM Information | This procedure copies existing setup information from the module. |
Invalidate All Fobs | This program will erase all key fobs from memory and then begin reprogramming. |
Next Available Slot | This program will add key fobs being programmed to the first open slot available in the module. |
Program Key Fob 1 |
|
Program Key Fob 2 |
|
Program Key Fob 3 |
|
Program Key Fob 4 |
|
Tire/Type/Pressure Selection |
|