• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
---|---|---|---|---|
Liftgate Module B+ | B153A 08, B396A 02 | B153A 08, B396A 02 | -- | -- |
Liftgate Module B+ | U0230 00 | U0230 00 | -- | -- |
Liftgate Position Sensor 5V Reference Voltage | B153E 02 | B153B 08 | 2 | B1019 00 |
Full Open Signal | B153E 08 | B153B 05 | 2 | -- |
Object Sensors Signal | B153F 02 | B153F 05 | B153F 05 | B153F 03, B153F 07 |
Open/Close Switches Signal | B2494 02 | 1, 2 | 1, 2 | -- |
Pawl Switch Signal | B153A 00 | B153A 08 | B153A 00 | B153A 08 |
Position Sensor Signal 1 | B153E 08 | B153E 08 | B153E 05 | -- |
Position Sensor Signal 2 | B153E 08 | B153A 08 | B153E 05 | B153E 08 |
Ratchet Switch Signal | B153A 00 | B153A 08 | B153A 00 | B153A 08 |
Sector Switch Signal | B153A 00 | B153A 00 | B153A 00 | B153A 08 |
Disengage Clutch Control | B396B 02 | B396B 04 | B396B 01 | -- |
Engage Clutch Control | B396B 02 | B396B 04 | B396B 01 | -- |
Liftgate Latch Cinch Control | B2495 02 | B2495 04 | B2495 01 | -- |
Liftgate Latch Release Control | B2495 02 | B2495 04 | B2495 01 | -- |
Liftgate Motor Close Control | B396A 02 | B396A 04 | B396A 01 | B153E 08 |
Liftgate Motor Open Control | B396A 02 | B396A 04 | B396A 01 | B153E 08 |
Full Open Low Reference | -- | B153B 05 | 2 | -- |
Liftgate Switches Low Reference | -- | B153A 08 | 1 | B153E 08 |
Position Sensor Low Reference | -- | B153E 08 | 2 | -- |
Liftgate Control Module Ground | -- | U0230 00 | 2 | -- |
1. Liftgate Switch Malfunction 2. Liftgate Malfunction |
The latch motor is a bi-directional motor and cinch or unlatch operation is the result of the direction of the motor rotation. The liftgate module (LGM) controls the latch motor through the control circuits by supplying power and ground in the appropriate polarity. The motor control circuits are monitored by the LGM prior to activation for a high or low condition and during motor operation for an insufficient current flow condition.
The system voltage is 9-16 volts.
The LGM detects a short to voltage in the liftgate latch motor open control circuit or the liftgate latch motor close control circuit.
The LGM detects a short to ground in the liftgate latch motor open control circuit or the liftgate latch motor close control circuit.
The LGM detects an open/high resistance in the liftgate latch motor open control circuit or the liftgate latch motor close control circuit.
The liftgate latch will be inoperative.
• | The DTC will be current for as long as the fault is present. |
• | When the fault is no longer present, the DTC will be a history DTC. |
• | A history DTC will clear after 50 ignition cycles. |
Whenever the LGM loses power or is disconnected, the ignition must be cycled OFF then ON in order to reactivate the LGM.
Liftgate Description and Operation
Control Module References for scan tool information
Ignition ON, command the liftgate to OPEN and CLOSE with the scan tool. The liftgate latch assembly should release the liftgate allowing the liftgate to open.
⇒ | If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If circuits test normal, replace the LGM. |
⇒ | If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If circuits test normal, replace the LGM. |
⇒ | If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the LGM. |
⇒ | If the test lamp is always ON, test the control circuit for a short to voltage, if the circuit tests normal, replace the LGM. |
⇒ | If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the LGM. |
⇒ | If the test lamp is always ON, test the control circuit for a short to voltage, if the circuit tests normal, replace the LGM. |
⇒ | If the function does not perform as specified, replace the liftgate latch. |
⇒ | If the function does not perform as specified, replace the liftgate latch. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for LGM replacement, setup and programming