System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inches H2O in a calibrated time, this DTC sets.
The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP canister purge and vent solenoid valves.
Control Module Command | EVAP Canister Purge Solenoid Valve | EVAP Canister Vent Solenoid Valve |
|---|---|---|
ON | Open | Closed |
OFF | Closed | Open |
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0446 EVAP Vent System Performance
Conditions for Running the DTC
| • | DTC P0449, P0451, P0452, P0453, P0454, P0498, P0499 are not set. |
| • | The EVAP canister purge solenoid valve must be active. |
| • | The engine is running. |
Conditions for Setting the DTC
The fuel tank pressure is less than -7 inches H2O with the EVAP canister vent solenoid valve commanded OFF.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem. |
| • | For intermittent conditions, refer to Intermittent Conditions . |
Step | Action | Values | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Evaporative Emissions Hose Routing Diagram | ||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||
2 | Inspect the evaporative emission (EVAP) system for the following conditions:
Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 3 | ||||||
3 |
Is the fuel tank pressure sensor parameter within the specified range? | -1 to +1 in H2O | Go to Step 4 | Go to Step 8 | ||||||
4 |
Important: DO NOT exceed the specified value in this step. Exceeding the specified value may produce incorrect test results.
Is the fuel tank pressure sensor parameter less than the second specified value? | 5 in H2O 1 in H2O | Go to Diagnostic Aids | Go to Step 5 | ||||||
5 | Disconnect the EVAP vent hose from the EVAP vent solenoid valve. Is the fuel tank pressure sensor parameter less than the specified value? | 1 in H2O | Go to Step 11 | Go to Step 6 | ||||||
6 | Disconnect the EVAP vent hose from the EVAP canister. Is the fuel tank pressure sensor parameter less than the specified value? | 1 in H2O | Go to Step 7 | Go to Step 12 | ||||||
7 | Repair the pinched or restricted EVAP vent hose. Did you complete the repair? | -- | Go to Step 13 | -- | ||||||
8 | Test for poor connections at the harness connector of the fuel tank pressure (FTP) sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 | ||||||
9 | Test the FTP sensor low reference circuit for an open or high resistance. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 10 | ||||||
10 | Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- | ||||||
11 | Replace the EVAP vent solenoid valve. Refer to Evaporative Emission Canister Vent Solenoid Valve Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- | ||||||
12 | Replace the EVAP canister. Refer to Evaporative Emission Canister Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- | ||||||
13 |
Is the fuel tank pressure sensor parameter within the specified range? | -1 to +1 in H2O | Go to Step 14 | Go to Step 2 | ||||||
14 |
Important: DO NOT exceed the specified value in this step. Exceeding the specified value may produce incorrect test results.
Is the fuel tank pressure sensor parameter less than the second specified value? | 5 in H2O 1 in H2O | Go to Step 15 | Go to Step 2 | ||||||
15 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK | ||||||
