Circuit Description
The 2-3 shift solenoid (SS) valve is a normally-closed exhaust valve that, in conjunction with the 1-2 shift solenoid (SS) valve, allows 4 different shifting combinations. The 2-3 SS valve is attached to the control valve body, within the transmission.
The TCM monitors the actual gear ratio, and compares the actual gear ratio with the commanded gear ratio. DTC P0756 sets under two conditions:
| • | A stuck OFF 2-3 SS valve |
| • | A stuck OFF 2-3 shift valve |
If the TCM detects a 5-3-4-4-5 shift pattern, then DTC P0756 sets. DTC P0756 is a type B DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0756 2-3 Shift Solenoid Valve Performance - No First or Second Gear
Conditions for Running the DTC
| • | No TP sensor DTC P0120. |
| • | No ISS DTCs P0716 or P0717. |
| • | No OSS DTCs P0722 or P0723. |
| • | No TCC stuck ON DTC P0742. |
| • | No shift solenoid electrical DTCs P0973, P0974, P0976, P0977, P0979, or P0980. |
| • | No IMS DTCs P1815, P1820, P1822, P1823, P1825 or P1826. |
| • | No engine torque delivered signal DTC P2637. |
| • | The engine run time is greater than 5 seconds. |
| • | The IMS range is not PARK, NEUTRAL or REVERSE. |
| • | The transmission fluid temperature is 20-130°C (68-266°F). |
| • | The throttle position is greater than 10 percent. |
| • | The input shaft speed is 200-6,800 RPM. |
| • | The output shaft speed is greater than 200 RPM. |
| • | The engine torque is greater than 32 N·m (24 lb ft). |
Conditions for Setting the DTC
Both of the following conditions must occur during the same trip:
| • | The TCM commands 1st gear when the engine torque is greater than 40 N·m (30 lb ft), and the resulting gear ratio is 0.73:1-0.77:1 for 2.8 seconds. |
| • | The TCM commands 2nd gear when the engine torque is greater than 36 N·m (27 lb ft) and the resulting gear ratio is 1.56:1-1.64:1 for 1 second. |
Action Taken When the DTC Sets
| • | The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The TCM inhibits 1st gear |
| • | The TCM commands maximum line pressure. |
| • | The TCM freezes transmission adaptive functions. |
| • | The ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as Freeze Frame and Failure Records. |
| • | The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Failure Records. |
| • | The TCM stores DTC P0756 in TCM history. |
Conditions for Clearing the DTC
| • | The ECM turns OFF the MIL after the third consecutive drive trip in which the TCM does not send a MIL illumination request. |
| • | A scan tool can clear the DTC. |
| • | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without a non emission related diagnostic fault occurring. |
| • | The TCM cancels the DTC default actions when the ignition is OFF long enough in order to power down the TCM. |
Diagnostic Aids
| • | If you clear DTC P0756, and then cannot reset DTC P0756, the following conditions may exist: |
| - | Fluid contamination |
| - | Plugged fluid circuits |
| - | Restricted fluid circuits |
| • | Refer to Shift Solenoid Valve State and Gear Ratio . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies a 5-3-4-4-5 shift pattern.
-
This step tests for a mechanical or hydraulic condition causing the 2-3 SS valve to be stuck OFF, or the circuit to be applied.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||||
2 | Perform the Transmission Fluid Checking Procedure. Refer to Transmission Fluid Check . Did you perform the Transmission Fluid Checking Procedure? | -- | Go to Step 3 | Go to Transmission Fluid Check | ||||||||
Important:
Are the commanded gear and gear ratio within the specified range? | 1st 0.73:1-0.77:1 2nd 1.56:1-1.64:1 | Go to Step 4 | Go to Intermittent Conditions in Engine Controls - 3.6L or Intermittent Conditions in Engine Controls - 4.6L | |||||||||
Refer to 2-3 Shift Solenoid Valve Replacement . Did you complete the repair? | -- | Go to Step 5 | -- | |||||||||
5 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 6 | Go to Step 2 | ||||||||
6 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
