Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Ambient Light Sensor Signal | B2645 00 | B2645 00 | B2645 00 | -- |
Left Front Turn Signal Lamp Control | 1 | 1 | 1 | -- |
Right Front Turn Signal Lamp Control | 1 | 1 | 1 | -- |
Ambient Light Sensor Low Reference | -- | B2645 00 | 2 | -- |
Turn Signal Lamp - LF Ground | -- | 1 | 1 | -- |
Turn Signal Lamp - RF Ground | -- | 1 | 1 | -- |
1. Turn Signal Lamps and/or Indicators Malfunction 2. Daytime Running Lamps Malfunction | ||||
Circuit/System Description
The ambient light sensor is used to monitor outside lighting conditions. The ambient light sensor provides a voltage signal that will vary between 0.2 and 4.9 volts depending on outside lighting conditions. The HVAC control module determines the ambient light conditions, DAY or NIGHT, based on the voltage from the ambient light sensor. The HVAC control module provides a low reference ground and 5-volt reference signal to the ambient light sensor. The ambient light sensor signal circuit is a direct input to the HVAC control module. The HVAC control module sends a message via serial data to the instrument panel module (IPM) indicating the outside light conditions based on the signal from the ambient light sensor. The IPM determines if outside lighting conditions are correct for either daytime running lights (DRL) or automatic lamp control (ALC) when the headlamp switch is in the AUTO position. In daylight conditions the IPM will command the DRLs ON. During low light conditions the IPM will command the low beam headlamps ON. Any function or condition that turns on the headlamps will cancel DRL operation. With the turn signal/multifunction switch in the OFF position, the DRLs which consists of the front turn signal lamps will either be turned ON or OFF after a 30-second delay, depending on whether daylight or low light conditions are sensed by the ambient light sensor.
Diagnostic Aids
Important: This diagnostic procedure assumes that the turn signal lamps are operating within specifications. If the turns signal lamps are inoperative, diagnose the turn signal malfunction before proceeding with the following diagnostic. Refer to Turn Signal Lamps and/or Indicators Malfunction.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, verify with a scan tool the Park Brake Switch parameter displays Released.
| ⇒ | If not the specified value, refer to Symptoms - Hydraulic Brakes |
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the sunload sensor assembly.
- Ignition OFF, scan tool OFF, doors CLOSED, test for less than 20 ohms between the low reference circuit terminal C and ground.
- Reconnect the sunload sensor assembly harness connector.
- Ignition ON, verify the scan tool Ambient Light Sensor parameter is greater than 0.2 volt.
- Verify the scan tool Ambient Light Sensor parameter is less than 4.9 volts.
- If all circuits test normal, replace the sunload sensor assembly.
| ⇒ | If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the HVAC control module. |
| ⇒ | If less than the specified range, test the signal circuit terminal D for a short to ground. If the circuit tests normal, replace the HVAC control module. |
| ⇒ | If greater than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the HVAC control module. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for HVAC control module replacement, setup, and programming |
