Fastener Tightening Specifications: Refer to Fastener Tightening Specifications.

High Mounted Stop Lamp Emblem Assembly Replacement

1

Emblem Assembly, High Mounted Stop Lamp Wreath

Tip

2

Emblem Assembly, High Mounted Stop Lamp Crest

Tip

Rear Compartment Lid Name Plate "4" Replacement

3

Plate Assembly, Rear Compartment Lid Name "4"

Tip

1. For additional information on emblem/nameplate replacement refer to Emblem/Nameplate Replacement.
2. Dimension (h) is 28 mm (1.10 in) from the lower horizontal edge of the rear compartment lid.
3. Dimension (i) is 28.5 mm (1.12 in) from the right vertical edge of the rear compartment lid.

Rear Compartment Lid Name Plate "STS" Replacement

4

Plate Assembly, Rear Compartment Lid Name "STS"

Tip

1. For additional information on emblem/nameplate replacement refer to Emblem/Nameplate Replacement.
2. Dimension (e) is 31 mm (1.22 in) from the lower horizontal edge of the rear compartment lid.
3. Dimension (f) is 10 mm (0.39 in) from the left vertical edge of the "4" emblem.

Rear Compartment Lid Name Plate "Cadillac" Replacement

5

Plate Assembly, Rear Compartment Lid Name "Cadillac"

Tip

1. For additional information on emblem/nameplate replacement refer to Emblem/Nameplate Replacement.
2. Dimension (d) is 20 mm (0.79 in) from the left vertical edge of the "STS" emblem.
3. Dimension (c) is 31 mm (1.22 in) from the lower horizontal edge of the rear compartment lid.

Rear Compartment Lid Name Plate "Northstar" Replacement

6

Plate Assembly, Rear Compartment Lid Name "Northstar"

Tip

1. For additional information on emblem/nameplate replacement refer to Emblem/Nameplate Replacement.
2. Dimension (a) is 67 mm (2.64 in) from the left vertical edge of the rear compartment lid.
3. Dimension (b) is 31 mm (1.22 in) from the lower horizontal edge of the rear compartment lid.

Preliminary Procedure

1. Using a J 25070 in a circular motion, warm the rear compartment lid emblems/nameplates prior to removal. Carefully clean the panel thoroughly prior to bonding the new emblems/nameplates to the rear compartment lid.
2. Ensure the rear compartment lid is in the closed position prior to the installation of the new emblems/nameplates.

Special Tools

J 25070 Heat Gun

1

Rear Compartment Lid Nameplate Assembly (Cadillac)

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Procedure

1. Clean the adhesive tape from the surface of the rear compartment lid and dry thoroughly before applying new nameplate.
2. Peel protective backing from emblem and ensure no foreign matter or dirt comes in contact with the adhesive backing prior to installation.
3. Install the emblem and apply pressure to ensure full adhesion to the rear compartment lid.

2

Rear Compartment Lid Emblem Assembly (STS Emblem)

Procedure

1. Clean the adhesive tape from the surface of the rear compartment lid and dry thoroughly before applying the new emblem.
2. Peel protective backing from the emblem and ensure no foreign matter or dirt comes in contact with the adhesive backing prior to installation.
3. Position the emblem to the rear compartment lid.
4. Install the emblem and apply pressure to ensure full adhesion to the rear compartment lid.

3

Rear Compartment Lid Emblem Assembly (V Emblem)

Procedure

1. Clean the adhesive tape from the surface of the rear compartment lid and dry thoroughly before applying the new emblem.
2. Peel protective backing from the emblem and ensure no foreign matter or dirt comes in contact with the adhesive backing prior to installation.
3. Install the emblem and apply pressure to ensure full adhesion to the rear compartment lid.