Electronic Brake Control Module Replacement Without JL7
Removal Procedure
Notice: To prevent equipment damage, never connect or disconnect the wiring harness connection from the EBCM with the ignition switch in the ON position.
Important:
• The ignition switch must be placed in the OFF mode ONLY, before disconnecting the negative battery cable during this procedure. If the ignition switch is accidentally placed into ignition ON engine OFF mode, the control modules will be activated
and disconnecting the negative cable will cause various DTCs to be set. Refer to
Keyless Entry System Description and Operation. • After the ignition switch is placed into OFF mode, a waiting period of 2 minutes must be observed to allow the high-speed LAN control modules to deactivate before disconnecting or connecting the negative battery cable during this procedure.
If the waiting period is not observed, one or more of these control modules may still be activated, causing various DTCs to be set.
- Place the ignition switch into OFF mode. DO NOT place the ignition switch into ignition ON engine OFF mode.
- Wait a minimum of 2 minutes to allow the high-speed LAN control modules to deactivate.
- Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
- Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
- Remove the front air deflector shield. Refer to Front Air Deflector Replacement.
- Remove the washer solvent container fasteners and position the washer solvent container aside to access the electronic brake control module (EBCM). Refer to Windshield Washer Solvent Container Replacement.
- Thoroughly clean the area around the EBCM of all dirt and debris.
- Release the EBCM electrical connector by pressing the retaining tab and rotating the locking lever forward.
- Remove the EBCM screws (1).
- Separate the EBCM (1) from the brake pressure modulator valve (BPMV).
Installation Procedure
- Clean the sealing surfaces of the BPMV and the EBCM.
- Install the EBCM (1) to the BPMV (2) while carefully aligning the internal pump motor connector (3).
- Install the EBCM screws (1).
- Tighten the EBCM screws in the sequence shown (1-4).
- Connect the EBCM electrical connector (1).
- Rotate the locking lever (2) rearward.
- Ensure the electrical connector and locking lever are fully engaged into the EBCM (3).
- Position the washer solvent container and install the fasteners. Refer to Windshield Washer Solvent Container Replacement.
- Install the front air deflector shield. Refer to Front Air Deflector Replacement.
- Lower the vehicle.
- Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
- If installing a new EBCM, program the EBCM. Refer to Control Module References.
- Perform the Diagnostic System Check - Vehicle.
Notice: Refer to Fastener Notice in the Preface section.
Tighten
Tighten the screws to 5 N·m (44 lb in).
Electronic Brake Control Module Replacement With JL7
Removal Procedure
Notice: To prevent equipment damage, never connect or disconnect the wiring harness connection from the EBCM with the ignition switch in the ON position.
Important:
• The ignition switch must be placed in the OFF mode ONLY, before disconnecting the negative battery cable during this procedure. If the ignition switch is accidentally placed into ignition ON engine OFF mode, the control modules will be activated
and disconnecting the negative cable will cause various DTCs to be set. Refer to
Keyless Entry System Description and Operation. • After the ignition switch is placed into OFF mode, a waiting period of 2 minutes must be observed to allow the high-speed LAN control modules to deactivate before disconnecting or connecting the negative battery cable during this procedure.
If the waiting period is not observed, one or more of these control modules may still be activated, causing various DTCs to be set.
- Place the ignition switch into OFF mode. DO NOT place the ignition switch into ignition ON engine OFF mode.
- Wait a minimum of 2 minutes to allow the high-speed LAN control modules to deactivate.
- Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
- Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
- Remove the front air deflector shield. Refer to Front Air Deflector Replacement.
- Remove the washer solvent container fasteners and position the washer solvent container aside to access the electronic brake control module (EBCM). Refer to Windshield Washer Solvent Container Replacement.
- Thoroughly clean the area around the EBCM of all dirt and debris.
- Release the EBCM electrical connector by pressing the retaining tab and rotating the locking lever forward.
- Remove the EBCM screws (1).
- Separate the EBCM (1) from the brake pressure modulator valve (BPMV).
Installation Procedure
- Clean the sealing surfaces of the BPMV and the EBCM.
- Install the EBCM (1) to the BPMV.
- Install the EBCM screws (1).
- Tighten the EBCM screws in the sequence shown (1-4).
- Connect the EBCM electrical connector.
- Position the washer solvent container and install the fasteners. Refer to Windshield Washer Solvent Container Replacement.
- Install the front air deflector shield. Refer to Front Air Deflector Replacement.
- Lower the vehicle.
- If installing a new EBCM, program the EBCM. Refer to Control Module References.
- Perform the Diagnostic System Check - Vehicle.
Notice: Refer to Fastener Notice in the Preface section.
Tighten
Tighten the screws to 5 N·m (44 lb in).
