The air temperature controls are divided into 4 primary areas:
• | The Heating and Air Conditioning System |
• | Auxiliary heating and A/C system |
HVAC Control Components
HVAC Control Module
The HVAC control module is a GMLAN device that interfaces between the operator and the HVAC system to maintain air temperature and distribution settings. The battery positive voltage circuit provides power that the control module uses for keep alive memory
(KAM). The instrument panel module (IPM), which is the vehicle power mode master, provides a device on signal. The control module supports the following features:
Feature
| Availability
|
Afterblow
| Available if reprogrammed by the technician
|
Purge
| No
|
Personalization
| Yes
|
Actuator Calibration
| No
|
Heated Seat Control
| Optional
|
Remote Start and Personalization
If the remote start personalization feature for climate control is selected through radio, the HVAC control module will receive information that defines the current driver of the vehicle from the Ezkey module through GMLAN communication. This information
shall be stored inside the HVAC control module memory. When a different key fob is selected, the HVAC control module will recall the appropriate driver settings. The full auto mode and previous set temp will be commanded if ambient air temperature is above 0°C
(32°F). Defrost mode will be commanded when the ambient air temperature is below 0°C (32°F). Upon a battery reset, the HVAC control module shall also set the driver ID to Driver#1. The HVAC system will memorize the following system configurations
for up to 2 unique drivers:
• | Passenger set temperature |
• | A/C compressor request, auto ON or A/C OFF |
If the remote start personalization feature for heated and vented seat control is selected through radio, if the inside air temperature is below 12°C (54°F) the heated seat will be commanded to high. If the inside air temperature is above 26°C
(80°F) and the ambient air temperature is above 21°C (70°F) the vented seat will be commanded to high. When the HVAC control module is first turned On or key On, the last stored settings for the current driver will be activated, heat/vented seat
control is carried over from remote start.
OnStar® Blower Control ON/OFF
During OnStar® audio control ON, the HVAC control module receives signals from OnStar® to reduce blower level to a level 4. OnStar® blower control becomes active in auto or manual blower operation. During this OnStar® blower control,
if in manual or auto blower, the display will show AUTO for blower display. This blower reduction is to ensure that all incoming and outgoing voice calls will be recognized by the OnStar® module. The driver is allowed to override the OnStar® auto blower
level by increasing or decreasing it manually to any desired level. When OnStar® no longer sends the request for blower control the HVAC control module will cancel OnStar® blower control and resume previous blower level if no manual override of the blower
was selected.
Air Temperature Actuators
The air temperature actuator is a 5-wire bi-directional electric motor that incorporates a feedback potentiometer. Low reference, 5-volt reference, position signal, and 2 control circuits enable the actuator to operate. The control circuits use
either a 0 or 12-volt value to coordinate the actuator movement. When the actuator is at rest, both control circuits have a value of 0 volts. In order to move the actuator, the HVAC control module grounds one of the control circuits while providing the
other with 12 volts. The HVAC control module reverses the polarity of the control circuits to move the actuator in the opposite direction. When the actuator shaft rotates, the potentiometers adjustable contact changes the door position signal between
0-5 volts. The HVAC control module uses a range of 0-255 counts to index the actuator position. The door position signal voltage is converted to a 0-255 count range. When the module sets a commanded, or targeted value,
one of the control circuits is grounded. As the actuator shaft rotates the changing position signal is sent to the module. Once the position signal and the commanded value are the same, the module removes power and ground from the control circuits.
Air Temperature Sensors
The air temperature sensors are 2-wire negative temperature co-efficient thermistors. The vehicle uses the following air temperature sensors:
A signal and low reference circuit enables the sensor to operate. As the air temperature surrounding the sensor increases, the sensor resistance decreases. The sensor signal decreases as the resistance decreases. The sensor signal varies between 0-5 volts.
The HVAC control module converts the signal to a range between 0-255 counts.
The inside temperature sensor operates within a temperature range between -6.5 to +57.5°C (+20.3 to +135.5°F). If the sensor is shorted to ground, voltage, or an open, the system will operate using an estimated default value to allow the
system to operate. The ambient sensor operates within a temperature range between -30 to +51°C (-22 to +123.8°F). If the HVAC control module has determined that the ambient temperature sensor has failed, the driver information center (DIC)
display shall display - - - - in place of the outside air temperature. If the sensor is shorted to ground, voltage, or an open, the system will operate using an estimated default value to allow the system to operate. If the engine coolant temperature is not
more than 3°C (5.4°F) above the sensor reading, or if the engine has not been started in 3 hours, then the actual ambient air temperature sensor reading is displayed. Also at vehicle speeds greater than 35 km/h (22 mph), the ambient
air temperature displayed may be allowed to increase, but only at a slow, filtered rate. The DIC displays the ambient air temperature value that it receives from the HVAC control module through a GMLAN message. The ambient air temperature value can be updated
by an outside air instant update feature.
To use this feature, press the following switches on the HVAC control module simultaneously:
Sunload Sensor
The sunload sensor is a 2-wire photo diode. The vehicle uses left and right sunload sensors. The 2 sensors are integrated into the sunload sensor assembly along with the ambient light sensor. Low reference and signal circuits enable the sensor to
operate. As the sunload increases, the sensor signal decreases. The sensor operates within an intensity range between completely dark and bright. The sensor signal varies between 0-5 volts. The HVAC control module converts the signal to a range
between 0-255 counts. The sunload sensor provides the HVAC control module a measurement of the amount of light shining on the vehicle. Bright or high intensity light causes the vehicle's inside temperature to increase. The HVAC system compensates
for the increased temperature by diverting additional cool air into the vehicle. If the sensor is open or shorted, no sunload adjustment occurs and the SERVICE A/C SYSTEM message is displayed.
Evaporator Temperature Sensor
The HVAC control module monitors the temperature of the air passing through the evaporator by the A/C evaporator air temperature sensor. This sensor is located on the evaporator core. The temperature is used to cycle the A/C compressor ON and OFF to prevent
the evaporator core from freezing. A thermistor inside the sensor varies its resistance to monitor the evaporator air temperature. The HVAC control module monitors the voltage drop across the thermistor when supplied with a 5-volt reference signal. The HVAC
control module will send a class 2 message to the engine control module (ECM) to stop requesting the A/C compressor clutch operation if the temperature drops below 3°C (37°F). The sensor must be above 4°C (39°F) to request the A/C compressor
clutch again.
The sensor operates within a temperature range between -40 to +215°C (-40 to +355°F). If the HVAC control module detects an open in the evaporator temperature sensor or circuit, the class 2 message sent to the ECM will not submit
the A/C ON request. The HVAC control module will then send a request to the radio for display of the SERVICE A/C SYSTEM that will be displayed on the DIC. The HVAC control module will also display A/C OFF on the module as long as the condition is present.
A/C Refrigerant Pressure Sensor
The A/C refrigerant pressure sensor is a 3-wire piezoelectric pressure transducer. A 5-volt reference, low reference, and signal circuits enable the sensor to operate. The A/C pressure signal can be between 0-5 volts. When the A/C refrigerant
pressure is low, the signal value is near 0 volts. When the A/C refrigerant pressure is high, the signal value is near 5 volts.
The A/C refrigerant pressure sensor prevents the A/C system from operating when an excessively high or low pressure condition exists.
If the ECM detects a failure in the A/C refrigerant pressure sensor or circuit, the class 2 message sent to the HVAC control module will be invalid. The HVAC control module will then send a request to the radio for display of the SERVICE A/C SYSTEM
that will be displayed on the DIC. The HVAC control module will also display A/C OFF on the module as long as the condition is present.
Air Quality Sensor (RPO K14)
Warning - The air quality sensor recognizes carbon monoxide but is not designed as a safety feature to protect you from carbon monoxide. The air quality sensor is designed to limit your exposure to gasoline exhaust fumes and or diesel exhaust fumes that
could enter into the passenger compartment from nearby vehicles for a limited amount of time.
The HVAC control module monitors the outside air quality while in AUTO mode via the air quality sensor assembly. You can activate the air quality sensor on your vehicle, if equipped, by pressing the Auto button on the HVAC module. The air quality sensor
is a 5-wire sensor, 1 ignition voltage circuit, 2 ground circuit, and 2 control circuits. There are 2 sensors inside the air quality sensor assembly. A hydro carbon (HC) sensor that is used for detecting gasoline exhaust fumes and
a Nox sensor that is used for detecting nitrous oxide, diesel exhaust fumes. The HVAC control module outputs a 5-volt signal on the HC and Nox control circuits and operates in a range between 0-5 volts.
The HVAC module updates the air quality sensor calibration approximately 4 times per second. The air quality sensor input to the HVAC module is compared to the previously updated air quality sensor calibration. If the voltage difference is great
enough the recirc actuator will be controlled to recirc, outside air, or partial recirc outside air position based on the air quality sensor input.
When air quality around the front of the vehicle is poor, the air quality sensor system operates as follows:
• | Poor air quality with high HC levels will cause the HC control circuit to read a lower voltage. |
• | Poor air quality with high Nox levels will cause the Nox control circuit to read a higher voltage. |
• | The recirculation actuator is forced to the recirculation position. |
• | The recirc symbol on the HVAC module will illuminate. |
• | The recirc icon will not illuminate if the recirc actuator is already in the auto recirc position. |
When air quality around the front of the vehicle is normal, the air quality sensor system operates as follows:
• | Normal air quality levels the HC control circuit will recognize very little voltage change from the previously updated calibration. |
• | Normal air quality levels the Nox control circuit will recognize very little voltage change from the previously updated calibration. |
• | The recirculation actuator position is not controlled by the air quality sensor system. |
The following are conditions that will prevent the air quality sensor from controlling the recirc actuator:
• | A/C OFF conditions (compressor OFF) prevents air quality sensor from changing the current position of the actuator) |
• | Coolant temperature below 37°C (99°F) during warm up will prevent the blower from operating and air quality sensor from controlling the recirc position. |
• | Outside air temperature less than 5°C (41°F) (prevents air quality sensor from changing the current position of the actuator) |
• | Outside air temperature less than 15°C (59°F) and A/C high side pressure less than 196 kpa (28 psi) (prevents air quality sensor from changing the current position of the actuator) |
• | 28 seconds sensor warm-up time after ignition is turned ON (prevents air quality sensor from changing the current position of the actuator) |
• | Evaporator temperature sensor failure |
• | Customer manually selects defrost or defog (forces actuator to outside air position) |
• | Customer manually selects recirc or outside air position |
• | Coolant temperature above 112°C (V8), 119°C (HFV6) the actuator is forced to the recirc position. When coolant temperature drops below 109°C (V8), 116°C (HFV6) forced recirc is canceled. |
• | A/C pressure above 2 500 KPA (362 psi) the actuator is forces to the recirc position. When A/C pressure drops below 2 000 KPA (290 psi) forced recirc is canceled. |
The following describes the recirc actuator function after the air quality sensor has canceled the command to recirc
• | Full recirc position will be held for 2 minutes when vehicle speed is less than 10 km/h (6.3 mph) after 2 minutes expires the recirc door will move to full outside air position. |
• | Partial recirc, outside air position will be held for 2 minutes when vehicle speed is above 20 km/h (12.5 mph) after 2 minutes expires the recirc door will move to full outside air position. |
• | Full outside air position if vehicle speed is greater than 60 km/h (37 mph) and blower is not on high speed. |
The instrument panel module (IPM) shall provide the GMLAN Option Information for "Climate Air Quality Sensor Present" and "Climate Control Air Quality Sensitivity Selection" to the HVAC control module. Based on the option information sent to the HVAC control
module by the IPM, the HVAC control module will choose 1 of 7 different sensitivity calibration settings stored in the HVAC module. The IPM sends the signal that tells the HVAC control module which sensitivity setting to use. From production the
IPM sends a GMLAN message of 0 which tells the HVAC control module to use the default level 4 sensitivity calibration. The air quality sensitivity message sent to the HVAC module can be changed through the IPM with a TECH 2 and has 7 different air quality sensor
calibration settings to choose from, 1 being the most sensitive to exhaust fumes and 7 being the least sensitive to exhaust fumes.
The driver information center (DIC) will display the SERVICE A/C SYSTEM message if the HVAC system has detected a short to ground in the air quality sensor circuit. An open circuit or a short to voltage in the air quality sensor circuit will be diagnosed
through symptom based diagnostics because both of these conditions will not turn on the SERVICE A/C SYSTEM message or set a trouble code.
Heating and A/C Operation
The purpose of the heating and A/C System is to provide the following:
• | Remove humidity from the interior of the vehicle |
• | Reduce windshield fogging |
Regardless of the temperature setting, the following can effect the rate that the HVAC system can achieve a desired temperature:
• | Recirculation actuator setting |
• | Difference between inside and desired temperature |
• | Difference between ambient and desired temperature |
• | Blower motor speed setting |
The HVAC control module commands or monitors the following actions when an air temperature setting is selected.
• | WARMEST POSITION--The air temperature actuator door position directs maximum air flow through the heater core. |
• | COLDEST POSITION--The air temperature actuator door position directs maximum air flow around the heater core. |
• | BETWEEN THE WARMEST AND COLDEST POSITION--The following sensors are monitored to direct the appropriate amount of air through the heater core to achieve the desired temperature: |
The A/C system is engaged by selecting any switch on the HVAC control module except the A/C OFF switch. The A/C switch will illuminate A/C OFF when the A/C switch is selected. The control module sends a GMLAN A/C request message to the engine control module
(ECM) for A/C compressor clutch operation. The following conditions must be met in order for the ECM to turn on the compressor clutch:
- | Evaporator Temperature more than 4°C (39°F) |
- | Control module operating range 9-16 volts |
- | Engine coolant temperature (ECT) is less than 125°C (257°F) or 120°C (248°F) for PV8 |
- | Engine RPM is between 0-6,000 RPM. |
- | A/C pressure is between 3 137 kPa (455 psi) or 2 850 kPa (413 psi) for PV8 and 193 kPa (28 psi) or 200 kPa (29 psi) for PV8. |
Once engaged, the compressor clutch will be disengaged for the following conditions:
• | Throttle position is 100 percent. |
• | A/C pressure is more than 3 137 kPa (455 psi) or 2 850 kPa (413 psi) for PV8. |
• | A/C pressure is less than 193 kPa (28 psi) or 200 kPa (29 psi) for PV8. |
• | Engine coolant temperature (ECT) is more than 125°C (257°F) or 120°C (248°F) for PV8. |
• | Engine speed is more than 5,500 RPM. |
• | ECM detects excessive torque load. |
• | ECM detects insufficient idle quality. |
• | ECM detects a hard launch condition. |
When the compressor clutch disengages, the compressor clutch diode protects the electrical system from a voltage spike.
Dual Zone Operation
The HVAC control module has temperature settings for the driver and the passenger. If the passenger setting is turned OFF then the driver setting controls both driver and passenger temperature actuators. The passenger setting cannot be used without the
driver setting also being ON. The passenger setting can be turned ON or OFF by pressing the power button in the center of the passenger temperature rocker switch. When the passenger setting is ON, the passenger temperature can be adjusted independently from
the driver setting and the passenger temperature is displayed on the passenger side of the control module. A different sunload on one side of the vehicle may cause different discharge air temperatures, even when the passenger setting is not turned ON.
Automatic Operation
In automatic operation, the HVAC control module will maintain the comfort level inside of the vehicle by controlling the A/C compressor clutch, the blower motor, the air temperature actuators, mode actuator and recirculation.
To place the HVAC system in automatic mode, the following is required:
• | The blower motor switch must be in the AUTO position. |
• | The air temperature switch must be in any other position other than 60 or 90 degrees. |
• | The mode switch must be in the AUTO position. |
Once the desired temperature is reached, the blower motor, mode, recirculation and temperature actuators will automatically adjust to maintain the temperature selected. The HVAC control module performs the following functions to maintain the desired air
temperature:
• | Regulate blower motor speed |
• | Position the air temperature actuator |
• | Position the mode actuator |
• | Position the recirculation actuator |
When the warmest position is selected in automatic operation, the blower speed will increase gradually, until the vehicle reaches normal operating temperature. When normal operating temperature is reached, the blower will stay on high speed and the air
temperature actuators will stay in the full heat position. When the coldest position is selected in automatic operation, the blower will stay on high and the air temperature actuators will stay in the full cold position.
In cold temperatures, the automatic HVAC system will provide heat in the most efficient manner. The vehicle operator can select an extreme temperature setting, but the system will not warm the vehicle any faster. In warm temperatures, the automatic HVAC
system will also provide air conditioning in the most efficient manner. Selecting an extremely cool temperature will not cool the vehicle any faster.
Auxiliary HVAC Control Module
The auxiliary HVAC control module is a non-GM LAN device that interfaces between the operator and the auxiliary HVAC system to maintain air temperature and air distribution settings. Five volts and ground are supplied to the rear HVAC control module. The
front HVAC control module monitors the position of the rear air temperature actuator and the rear mode actuator. The front HVAC module will move the actuators to the proper position when it receives a request from the rear HVAC control module on which position
to place the actuator.
Auxiliary Heating and A/C Operation
The auxiliary HVAC control module provides airflow direction and temperature control for the back seat passengers. Passengers can operate the rear HVAC control module in both manual or automatic modes. Auxiliary HVAC temperatures can be set cooler or warmer
than the front primary HVAC setting. The front HVAC module provides power and ground to the auxiliary air temperature actuator. The front HVAC module receives power through the ignition 1 and battery positive voltage circuits from the underhood fuse block.
The auxiliary air temperature actuator is a reverse polarity motor. Each circuit provides both power and ground to the auxiliary air temperature actuator. When the auxiliary air temperature actuator is being held in position, both of the auxiliary air temperature
door control circuits have 0 volts applied to both sides of the actuator motor. This holds the actuator stationary. When a cooler temperature is requested, one of the auxiliary air temperature door control circuits will ground, driving the auxiliary air temperature
actuator to the desired temperature. When a warmer temperature is requested, the other auxiliary air temperature door control circuit will ground. This moves the auxiliary air temperature actuator into the desired position.
Auxiliary Air Temperature Actuator
The auxiliary air temperature actuator is a 5-wire bi-directional electric motor that incorporates a feedback potentiometer. Low reference, 5-volt reference, position signal, and 2 control circuits enable the actuator to operate. The control circuits use
either a 0 or 12-volt value to coordinate the actuator movement. When the actuator is at rest, both control circuits have a value of 0 volts. In order to move the actuator, the HVAC control module grounds one of the control circuits while providing the
other with 12 volts. The HVAC control module reverses the polarity of the control circuits to move the actuator in the opposite direction. When the actuator shaft rotates, the potentiometers adjustable contact changes the door position signal between
0-5 volts. The HVAC control module uses a range of 0-255 counts to index the actuator position. The door position signal voltage is converted to a 0-255 count range. When the module sets a commanded, or targeted value, one of the control
circuits is grounded. As the actuator shaft rotates, the changing position signal is sent to the module. Once the position signal and the commanded value are the same, the module removes power and ground from the control circuits.
Steering Wheel Controls
The voice recognition has the ability to control the HVAC output air temperature, fan speed and defrost selections. The radio will recognize the following verbal commands when the steering wheel switch is pressed for controlling specific HVAC controls:
For heater or A/C On the following commands will be recognized:
For heater or A/C Off the following commands will be recognized:
For heater or A/C fan high the following commands will be recognized:
• | Air-conditioning Fan High |
For heater or A/C fan low the following commands will be recognized:
• | Air-conditioning Fan Low |
For heater or A/C fan auto the following commands will be recognized:
• | Air-conditioning Fan Auto |
For heater or A/C temperature change the following commands will be recognized:
• | Heater Temp (or Temperature) 16-30°C or 60-90°F |
• | Heat Temp (or Temperature) 16-30°C or 60-90°F |
• | A/C Temp (or Temperature) 16-30°C or 60-90°F |
• | Air-conditioning Temp (or Temperature) 16-30°C or 60-90°F |
For heater or A/C Defrost the following commands will be recognized:
• | Heater Defog (or Defrost) On |
• | Heat Defog (or Defrost) On |
• | A/C Defog (or Defrost) On |
• | Air-conditioning Defog (or Defrost) On |
For heater or A/C Defrost the following commands will be recognized:
• | Heater Defog (or Defrost) Off |
• | Heat Defog (or Defrost) Off |
• | A/C Defog (or Defrost) Off |
• | Air-conditioning Defog (or Defrost) Off |
For heater or A/C Front Defrost the following commands will be recognized:
• | Heater Front Defog (or Defrost) On |
• | Heat Front Defog (or Defrost) On |
• | A/C Front Defog (or Defrost) On |
• | Air-conditioning Front Defog (or Defrost) On |
For heater or A/C Front Defrost the following commands will be recognized:
• | Heater Front Defog (or Defrost) Off |
• | Heat Front Defog (or Defrost) Off |
• | A/C Front Defog (or Defrost) Off |
• | Air-conditioning Front Defog (or Defrost) Off |
For heater or A/C Rear Defrost the following commands will be recognized:
• | Heater Rear Defog (or Defrost) On |
• | Heat Rear Defog (or Defrost) On |
• | A/C Rear Defog (or Defrost) On |
• | Air-conditioning Rear Defog (or Defrost) On |
For heater or A/C Rear Defrost the following commands will be recognized:
• | Heater Rear Defog (or Defrost) Off |
• | Heat Rear Defog (or Defrost) Off |
• | A/C Rear Defog (or Defrost) Off |
• | Air-conditioning Rear Defog (or Defrost) Off |
A/C Cycle
Refrigerant is the key element in an air conditioning system. R-134a is presently the only EPA approved refrigerant for automotive use. R-134a is a very low temperature gas that can transfer the undesirable heat and moisture from the passenger compartment
to the outside air.
The Denso 7SBU16 variable displacement swash plate A/C compressor is belt driven and operates when the magnetic clutch is engaged. The compressor builds pressure on the vapor refrigerant. Compressing the refrigerant also adds heat to the refrigerant. The
refrigerant is discharged from the compressor, through the discharge hose, and forced to flow to the condenser and then through the balance of the A/C System. The A/C System is mechanically protected with the use of a high pressure relief valve.
If the high pressure switch were to fail or if the refrigerant system becomes restricted and refrigerant pressure continues to rise, the high pressure relief will pop open and release refrigerant from the system.
Compressed refrigerant enters the condenser in a high temperature, high pressure vapor state. As the refrigerant flows through the condenser, the heat of the refrigerant is transferred to the ambient air passing through the condenser. Cooling the refrigerant
causes the refrigerant to condense and change from a vapor to a liquid state.
The condenser is located in front of the radiator for maximum heat transfer. The condenser is made of aluminum and aluminum cooling fins, which allow rapid heat transfer for the refrigerant. The semi-cooled liquid refrigerant exits the condenser and flows
through the liquid line, to the thermal expansion valve.
The thermal expansion valve is located in the liquid line between the condenser and the evaporator. The thermal expansion valve is the dividing point for the high and the low pressure sides of the A/C System. As the refrigerant passes through the thermal
expansion valve, the pressure of the refrigerant is lowered. Due to the pressure differential of the liquid refrigerant, the refrigerant will begin to vaporize at the thermal expansion valve. The thermal expansion valve also meters the amount of liquid refrigerant
that can flow into the evaporator.
Refrigerant exiting the thermal expansion valve flows into the evaporator core in a low pressure, liquid state. Ambient air is drawn through the HVAC module and passes through the evaporator core. Warm and moist air will cause the liquid refrigerant boil
inside of the evaporator core. The boiling refrigerant absorbs heat from the ambient air and draws moisture onto the evaporator. The refrigerant exits the evaporator back through the thermal expansion valve and into the suction line and back to the compressor,
in a vapor state completing the A/C cycle of heat removal. At the compressor, the refrigerant is compressed again and the cycle of heat removal is repeated.
The conditioned air is distributed through the HVAC module for passenger comfort. The heat and moisture removed from the passenger compartment will also change form, or condense, and is discharged from the HVAC module as water under the vehicle.