Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B3006 5A: Hood Ajar Circuit Plausibility FailureDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Hood Open Switch Signal | B3006 5A | B3006 5A | B3006 5A | -- |
Hood Closed Switch Signal | B3006 5A | B3006 5A | B3006 5A | -- |
Ground | -- | B3006 5A | B3006 5A | -- |
Circuit/System Description
The rear integration module (RIM) monitors the voltage input of the hood open switch signal circuit and the hood closed switch signal circuit. With the hood open, the hood open portion of the switch is closed, grounding the hood open switch signal circuit from the RIM, and the hood closed portion of the switch is open. With the hood closed, the hood closed portion of the switch is closed, grounding the hood closed switch signal circuit from the RIM, and the hood ajar portion of the switch is open. During proper operation, the two separate voltage signals at the RIM should never be equal.
Conditions for Running the DTC
Battery voltage is between 9-16 volts
Conditions for Setting the DTC
Both the hood open switch signal and the hood closed switch signal are simultaneously in an active or inactive state
Action Taken When the DTC Sets
| • | Remote start functions will be disabled. |
| • | The hood ajar switch inputs will be ignored by content theft deterrent (CTD). |
Conditions for Clearing the DTC
| • | A current DTC will clear when the condition for setting the DTC are no longer present |
| • | A history DTC will clear at 40 malfunction-free ignition cycles |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Keyless Entry System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool RIM Hood Open Switch and Hood Closed Switch parameters. With the hood open, the Hood Open Switch parameter should read Active and the Hood Closed Switch parameter should read Inactive. With the hood closed, the Hood Open Switch parameter should read Inactive and the Hood Closed Switch parameter should read Active.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the hood ajar switch.
- Ignition OFF, test for less than 10 ohms between the ground circuit terminal C and ground.
- Ignition ON, verify the scan tool Hood Closed Switch and Hood Open Switch parameters are Inactive.
- Install a 3A fused jumper wire between the signal circuit terminal A and ground. Verify the scan tool Hood Open Switch parameter is Active.
- Install a 3A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool Hood Closed Switch parameter is Active.
- If all circuits test normal, test or replace the hood ajar switch.
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If not the specified value, test the appropriate signal circuit for a short to ground. If the circuit tests normal, replace the RIM. |
| ⇒ | If not the specified value, test the signal circuit for a short to voltage or and open/high resistance. If the circuit tests normal, replace the RIM. |
| ⇒ | If not the specified value, test the signal circuit for a short to voltage or and open/high resistance. If the circuit tests normal, replace the RIM. |
Component Testing
Hood Ajar Switch
- Ignition OFF, disconnect the harness connector at the hood ajar switch.
- With the switch in the hood closed position, test for infinite resistance between the ground terminal C and the signal terminal A.
- Test for less than 2.0 ohms between the ground terminal C and the signal terminal B.
- With the switch in the hood open position, test for infinite resistance between the ground terminal C and the signal terminal B.
- Test for less than 2.0 ohms between the ground terminal C and the signal terminal A.
| ⇒ | If not infinite, replace the hood ajar switch. |
| ⇒ | If greater than the specified range, replace the hood ajar switch. |
| ⇒ | If not infinite, replace the hood ajar switch. |
| ⇒ | If greater than the specified range, replace the hood ajar switch. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for RIM replacement, programming and setup |
