Battery Positive Cable Replacement LH2 With Top Post

Removal Procedure

Note: 

•	Always route the replacement cable the same way as the original cable.

1. Remove the right compartment sight shield. Refer to Front Compartment Sight Shields Replacement.
2. Disconnect the battery negative cable (2). Refer to Battery Negative Cable Disconnection and Connection.



3. Rotate the lever (2) on the battery clamp to disengage the clamp.
4. Disconnect the battery positive cable from the battery (3).
5. Open the jump start terminal cover on the side of the under hood fuse block.



6. Remove the nut (1) securing the battery positive cable (2) to the under hood fuse block.
7. Disconnect the cable retaining clip from the right engine harness retainer.
8. Remove the intake manifold. Refer to Intake Manifold Replacement.



9. Remove the positive battery cable (2) from the starter motor.
10. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle
11. Remove the generator output nut and cable.
12. Disconnect the right engine harness retainer bracket from the head and reposition aside.
13. Release the generator output wire from the bracket
14. Remove the positive battery cable from the retaining features on the engine wiring harness bracket.
15. Remove the positive battery cable from the vehicle.

Installation Procedure

1. Position the battery positive cable to the engine.

Caution: Refer to Fastener Caution in the Preface section.

2. Connect the battery positive cable (2) to the starter and install the starter terminal nut and tighten to 10 N·m (89 lb in).
3. Connect the positive battery cable to the retaining features on the engine wiring harness bracket.
4. Connect the generator output wire to the bracket
5. Connect the right engine harness retainer bracket to the head.
6. Connect the generator output nut and cable and tighten to 10 N·m (89 lb in)..
7. Install the positive battery cable to the retaining features on the engine wiring harness bracket.
8. Install the intake manifold. Refer to Intake Manifold Replacement.
9. Connect the cable retaining clip to the stud.



10. Install battery positive cable (2) and nut (1) to the under hood fuse block and tighten to 15 N·m (11 lb ft).
11. Close the jump start terminal cover on the side of the under hood fuse block.



12. Connect the battery positive cable to the battery (3).
13. Rotate the lever (2) on the battery clamp to engage the clamp
14. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
15. Install the right compartment sight shield. Refer to Front Compartment Sight Shields Replacement.

Battery Positive Cable Replacement LH2 With Side Post

Removal Procedure

Note: 

•	Always route the replacement cable the same way as the original cable.

1. Disconnect the battery negative cable (2). Refer to Battery Negative Cable Disconnection and Connection.
2. Disconnect the battery positive cable (1) from the battery.



3. Remove the wiring harness from the retaining features on the underhood fuse block cover.
4. Depress the tabs in order to remove the underhood fuse block cover from the underhood fuse block.



5. Remove the nut (1) securing the battery positive cable (2) to the underhood fuse block.
6. Disconnect the cable retaining clip from the stud.
7. Remove the intake manifold. Refer to Intake Manifold Replacement.



8. Remove the positive battery cable (2) from the starter motor.
9. Remove the positive battery cable from the retaining features on the engine wiring harness bracket.
10. Remove the positive battery cable from the vehicle.

Installation Procedure

1. Position the battery positive cable to the engine.
2. Install the positive battery cable to the retaining features on the engine wiring harness bracket.

Caution: Refer to Fastener Caution in the Preface section.

3. Connect the battery positive cable (2) to the starter and install the starter terminal nut and tighten to 10 N·m (89 lb in).



4. Install the intake manifold. Refer to Intake Manifold Replacement.
5. Connect the cable retaining clip to the stud.
6. Install battery positive cable (2) and nut (1) to the underhood fuse block and tighten to 15 N·m (11 lb ft).



7. Install the underhood fuse block cover to the underhood fuse block.
8. Install the wiring harness to the retaining features on the underhood fuse block cover.



9. Connect the battery positive cable to the battery and tighten to 17 N·m (13 lb ft).
10. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.

Battery Positive Cable Replacement LY7 , LLT With Top Post

Removal Procedure

Note: 

•	Always route the replacement cable the same as the original cable.

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.



2. Rotate the lever (2) on the battery clamp to disengage the clamp.
3. Disconnect the battery positive cable from the battery (3).



4. Depress the tabs in order to remove the cover from the electrical center.



5. Remove the nut (1) securing the battery positive cable (2) to the electrical center.
6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.



7. Reposition the protective boot from the generator output BAT terminal for access.
8. Remove the generator output BAT terminal nut (3) and disconnect the battery positive lead (2) from the generator.



9. Remove the starter terminal nut (1) and disconnect the battery positive cable (2) from the starter.
10. Remove the battery positive cable from the engine.

Installation Procedure

1. Position the battery positive cable to the engine.

Caution: Refer to Fastener Caution in the Preface section.




2. Connect the battery positive cable (2) to the starter and install the starter terminal nut (1) and tighten to 13 N·m (115 lb in).



3. Connect the battery positive lead (2) to the generator and install the generator BAT terminal nut (3) and tighten to 13 N·m (115 lb in).
4. Install the protective boot to the generator output BAT terminal.
5. Lower the vehicle.



6. Install the nut (1) securing the battery positive cable (2) to the underhood fuse block and tighten to 15 N·m (11 lb ft).



7. Install the electrical center cover.



8. Connect the battery positive cable to the battery (3).
9. Rotate the lever (2) on the battery clamp to engage the clamp
10. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.

Battery Positive Cable Replacement LY7 With Side Post

Removal Procedure

Note: 

•	Always route the replacement cable the same as the original cable.

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
2. Disconnect the battery positive cable from the battery.



3. Depress the tabs in order to remove the cover from the electrical center.



4. Remove the nut (1) securing the battery positive cable (2) to the electrical center.



5. Reposition the protective boot from the generator output BAT terminal for access.
6. Remove the generator output BAT terminal nut (3) and disconnect the battery positive lead (2) from the generator.



7. Remove the starter terminal nut (1) and disconnect the battery positive cable (2) from the starter.
8. Lower the vehicle.
9. Remove the battery positive cable from the engine.

Installation Procedure

1. Position the battery positive cable to the engine.
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.

Caution: Refer to Fastener Caution in the Preface section.




3. Connect the battery positive cable (2) to the starter and install the starter terminal nut (1) and tighten to 13 N·m (115 lb in).



4. Connect the battery positive lead (2) to the generator and install the generator BAT terminal nut (3) and tighten to 3 N·m (115 lb in).
5. Install the protective boot to the generator output BAT terminal.
6. Lower the vehicle.



7. Install the nut (1) securing the battery positive cable (2) to the underhood fuse block and tighten to 15 N·m (11 lb ft).



8. Install the electrical center cover.



9. Connect the battery positive cable to the battery and tighten to 17 N·m (13 lb ft).
10. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.

Battery Positive Cable Replacement LC3

Removal Procedure

Note: 

•	Always route the replacement cable the same way as the original cable.

1. Disconnect the battery negative cable (2). Refer to Battery Negative Cable Disconnection and Connection.
2. Disconnect the battery positive cable (1) from the battery.



3. Remove the wiring harness from the retaining features on the underhood fuse block cover.
4. Depress the tabs in order to remove the underhood fuse block cover from the underhood fuse block.



5. Remove the nut (1) securing the battery positive cable (2) to the underhood fuse block.
6. Disconnect the cable retaining clip from the stud.
7. Remove the supercharger assembly. Refer to Supercharger Replacement.



8. Remove the positive battery cable (2) from the starter motor.
9. Remove the positive battery cable from the retaining features on the engine wiring harness bracket.
10. Remove the positive battery cable from the vehicle.

Installation Procedure

1. Position the battery positive cable to the engine.
2. Install the positive battery cable to the retaining features on the engine wiring harness bracket.

Caution: Refer to Fastener Caution in the Preface section.

3. Connect the battery positive cable (2) to the starter and install the starter terminal nut and tighten to 10 N·m (89 lb in).



4. Install the supercharger. Refer to Supercharger Replacement.
5. Connect the cable retaining clip to the stud.
6. Install battery positive cable (2) and nut (1) to the underhood fuse block and tighten to 15 N·m (11 lb ft)



7. Install the underhood fuse block cover to the underhood fuse block.
8. Install the wiring harness to the retaining features on the underhood fuse block cover.



9. Connect the battery positive cable to the battery and tighten to 17 N·m (13 lb ft).
10. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.