Brake Intermediate Hose Replacement JE5, JL9

Note: The intermediate brake hose assembly is serviced as an assembly.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the right rear tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
3. Clean all dirt and foreign material from the brake hose and the brake pipe fittings.



4. Disconnect the crossover brake pipe fitting (1) from the intermediate brake hose assembly (3).

Cap the brake pipe fitting to prevent brake fluid loss and contamination.

5. Using a flat-bladed tool, remove the brake hose retainer (2) from the rear frame bracket.
6. Disconnect the brake pipe fittings from the intermediate brake hose assembly.

Cap the brake pipe fittings to prevent brake fluid loss and contamination.




7. Disconnect the brake hose fitting bolt (4)  from the brake caliper (1).
8. Disconnect the brake hose from the brake caliper.

Plug the brake caliper inlet port to prevent brake fluid loss and contamination.

9. Place a shop towel on a hard surface.
10. Tap the threaded end of the brake hose fitting bolt on the shop towel to remove the gaskets (3) from the bolt (4)
11. Remove and discard the 2 copper brake hose gaskets (3). These gaskets may be stuck to the brake caliper and/or the brake hose end (2).



12. Remove the intermediate brake hose assembly mounting nuts (1) from the studs.
13. Remove the intermediate brake hose assembly (2) from the vehicle.

Caution: Make sure the brake hose is not twisted or kinked after installation. Damage to the hose could result.

1. Install the intermediate brake hose assembly (2) to the mounting studs.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the intermediate brake hose assembly mounting nuts (1) to the mounting studs and tighten to  14 N·m (124 lb in).
3. Remove the caps from the (2) intermediate brake pipe fittings.
4. Connect the 2 brake pipe fittings to the intermediate brake hose assembly.
5. Remove the plug from the brake caliper inlet port.




Note: Install NEW copper brake hose gaskets.

6. Assemble the brake hose (2), the NEW copper brake hose gaskets (3), and the brake hose fitting bolt (4) to the brake hose.
7. Install the brake hose fitting bolt to the brake caliper (1) and tighten to  50 N·m (37 lb ft).



8. Remove the cap from the crossover brake pipe fitting.
9. Install the brake hose retainer (2) to the rear frame bracket.
10. Connect the crossover brake pipe fitting (1) to the intermediate brake hose assembly (3) and tighten to  18 N·m (13 lb ft).
11. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
12. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
13. Lower the vehicle.

Brake Intermediate Hose Replacement J56

Note: The intermediate brake hose assembly is serviced as an assembly.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the right rear tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
3. Clean all dirt and foreign material from the brake hose and the brake pipe fittings.



4. Disconnect the crossover brake pipe fitting (1) from the intermediate brake hose assembly (3).

Cap the brake pipe fitting to prevent brake fluid loss and contamination.

5. Using a flat-bladed tool, remove the brake hose retainer (2) from the rear frame bracket.
6. Disconnect the brake pipe fittings from the intermediate brake hose assembly.

Cap the brake pipe fittings to prevent brake fluid loss and contamination.




7. Disconnect the brake hose fitting bolt (4)  from the brake caliper (1).
8. Disconnect the brake hose from the brake caliper.

Plug the brake caliper inlet port to prevent brake fluid loss and contamination.

9. Place a shop towel on a hard surface.
10. Tap the threaded end of the brake hose fitting bolt on the shop towel to remove the gaskets (3) from the bolt (4)
11. Remove and discard the 2 copper brake hose gaskets (3). These gaskets may be stuck to the brake caliper and/or the brake hose end (2).



12. Remove the intermediate brake hose assembly mounting nuts (1) from the studs.
13. Remove the intermediate brake hose assembly (2) from the vehicle.

Caution: Make sure the brake hose is not twisted or kinked after installation. Damage to the hose could result.

1. Install the intermediate brake hose assembly (2) to the mounting studs.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the intermediate brake hose assembly mounting nuts (1) to the mounting studs and tighten to  14 N·m (124 lb in).
3. Remove the caps from the (2) intermediate brake pipe fittings.
4. Connect the 2 brake pipe fittings to the intermediate brake hose assembly.
5. Remove the plug from the brake caliper inlet port.




Note: Install NEW copper brake hose gaskets.

6. Assemble the brake hose (2), the NEW copper brake hose gaskets (3), and the brake hose fitting bolt (4) to the brake hose.
7. Install the brake hose fitting bolt to the brake caliper (1) and tighten to  34 N·m (25 lb ft).



8. Remove the cap from the crossover brake pipe fitting.
9. Install the brake hose retainer (2) to the rear frame bracket.
10. Connect the crossover brake pipe fitting (1) to the intermediate brake hose assembly (3) and tighten to  18 N·m (13 lb ft).
11. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
12. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
13. Lower the vehicle.