Accident With or Without Air Bag Deployment - Component Inspections
Warning: Proper operation of the Supplemental Inflatable Restraint (SIR) sensing system requires that any repairs to the vehicle structure return the vehicle structure to the original production configuration.
Not properly repairing the vehicle structure could cause non-deployment of the air bag(s) in a frontal collision or deployment of the air bag(s) for conditions less severe than intended.
Warning: Proper operation of the Supplemental Inflatable Restraint (SIR) sensing system requires that any repairs to the vehicle structure return the vehicle structure to the original production configuration.
Not properly repairing the vehicle structure could cause non-deployment of the side impact air bag(s) in a side impact collision or deployment of the side impact air bag(s) for conditions less severe than intended.
After any collision, inspect the following components as indicated. If you detect any damage, replace the component. If you detect any damage to the mounting points or mounting hardware, repair the component or replace the hardware as needed.
| • | The instrument panel (I/P) knee bolsters and mounting points--Inspect the knee bolsters for bending, twisting, buckling, or any other type of damage. |
| • | The I/P brackets, braces, etc.--Inspect for bending, twisting, buckling, or any other type of damage. |
| • | The I/P cross car beam--Inspect for bending, twisting, buckling, or any other type of damage. |
| • | The I/P mounting points and brackets--Inspect for bending, twisting, buckling, or any other type of damage. |
| • | The seats and seat mounting points--Inspect for bending, twisting, buckling, or any other type of damage. |
| • | Passenger seat bottom equipped with Passenger Presence System (PPS)--Check for any DTCs or problems that may cause the PPS not to function properly. |
| • | The roof and headliner mounting points |
Accident With Frontal Air Bag Deployment - Component Replacement and Inspections
After a collision involving air bag deployment, replace the following components.
Note: The front passenger seat is equipped with a PPS, which detects an occupant. If the requirements for disabling the I/P air bag are met, then the PPS will communicate with the sensing and diagnostic module (SDM) to disable/turn
OFF the I/P air bag, even in a accident. For more information on the PPS, refer to
SIR System Description and Operation.
| • | Inflatable restraint I/P module, if deployed and after performing the necessary inspections listed above |
| • | Inflatable restraint steering wheel module |
| • | Inflatable restraint SDM |
| • | Inflatable restraint front end sensors |
| • | Inflatable restraint side impact modules, front seat air bags, if deployed |
| • | Inflatable restraint seat belt pretensioners |
Perform additional inspections on the following components:
| • | Steering wheel module coil and the coil wiring pigtail--Inspect for melting, scorching, or other damage due to excessive heat. |
| • | Mounting points or mounting hardware for the I/P module, steering wheel module, SDM, and pretensioners--Inspect for any damage and repair or replace each component as needed. |
Accident With Side Air Bag Deployment - Component Replacement and Inspections
After a collision involving side air bag deployment, replace the following components:
| • | Inflatable restraint side impact sensors (SIS), on the side of the impact |
| • | Inflatable restraint roof rail module, on the side of the impact |
| • | Inflatable restraint side impact modules, front seat air bags, if deployed |
| • | Inflatable restraint SDM |
| • | Inflatable restraint seat belt pretensioner |
Perform additional inspections on the following components:
| • | Mounting points or mounting hardware for the SIS, and side impact module on the side of impact--Inspect for any damage and repair or replace each component as needed. |
| • | Mounting points or mounting hardware for the roof rail module on the side of impact--Inspect for any damage and repair or replace each component as needed. |
| • | Mounting points or mounting hardware for the SDM and seat belt pretensioners--Inspect for any damage and repair or replace each component as needed. |
Sensor Replacement Guidelines
The SIR/side air bag sensor replacement policy requires replacing sensors in the area of accident damage. The area of accident damage is defined as the portion of the vehicle which is crushed, bent, or damaged due to a collision. An example of this would
be a moderate collision where the front of the vehicle impacts a tree. If the vehicle has an SIR sensor mounted forward of the radiator, it must be replaced.
| • | Replace the sensor whether or not the air bags have deployed. |
| • | Replace the sensor even if it appears to be undamaged. |
Sensor damage which is not visible, such as slight bending of the mounting bracket or cuts in the wire insulation, can cause improper operation of the SIR/side air bag sensing system. Do not try to determine whether the sensor is undamaged. Replace the
sensor. Also, if you follow a diagnostic trouble code (DTC) table and a malfunctioning sensor is indicated, replace the sensor.
