Diagnostic Trouble Code (DTC) Identification Diagnostic Types
DTC
| Description
| DTC Type*
| Default Action
|
P0218
| Automatic Transmission Fluid over Temperature
| C
|
| • | DTC P0218 is stored in PCM memory |
| | IDLE ENGINE TRANSMISSION HOT message displays |
|
P0502
| Vehicle Speed Sensor-Low
Input
| A
|
| • | DTC P0502 stores in PCM memory |
| • | SERVICE ENGINE SOON, SPEED SENSOR FAULT displays |
| • | Disable upshift and steady state adapts |
| • | Inhibit torque management |
| • | Calculate VSS from ISS and commanded gear |
|
P0503
| Vehicle Speed Sensor-Intermittent
| A
|
| • | DTC P0503 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SPEED SENSOR FAULT displays |
| • | Disable upshift and steady state adapts |
| • | Inhibit torque management |
| • | Calculate VSS from ISS and commanded gear |
|
P0711
| Automatic Transmission
Fluid Temperature Sensor-Range/Performance
| D
|
| • | DTC P0711 is stored in PCM memory |
| • | If any engine coolant temperature sensor codes are set, then the
transmission defaults to a temperature of 132°C (269°F) |
| • | If the engine coolant temperature is greater than 110°C (230°F),
then the transmission will default to a temperature of 132°C (269°F).
This will enable Transmission Hot Mode. The transmission remains in Hot Mode
until the engine coolant temperature drops below 105°C (221°F). If
the engine run time is less than 5 min, then the transmission defaults
to the intake air temperature at ignition ON. |
| • | If the engine coolant temperature is between 70°-110°C
(158°-230°F), then the transmission default temperature equals ECT - 10°C
when the intake air temperature is less than 80°C (176°F) at ignition
ON. If the intake air temperature is greater than 80°C (176°F) at
ignition ON, then the transmission default temperature equals ECT + 10°C. |
| • | If none of the above conditions exist, then the transmission
default temperature is 80°C (176°F) |
|
P0712
| Automatic Transmission
Fluid Temperature Sensor-Low Input
| D
|
| • | DTC P0712 is stored in PCM memory |
| • | If any engine coolant temperature sensor codes are set, then the
transmission defaults to a temperature of 132°C (269°F) |
| • | If the engine coolant temperature is greater than 110°C (230°F),
then the transmission will default to a temperature of 132°C (269°F).
This will enable Transmission Hot Mode. The transmission remains in Hot Mode
until the engine coolant temperature drops below 105°C (221°F) If
the engine run time is less than 5 min, then the transmission defaults
to the intake air temperature at ignition ON. |
| • | If the engine coolant temperature is between 70°-110°C
(158°-230°F), then the transmission default temperature equals ECT - 10°C
when the intake air temperature is less than 80°C (176°F) at ignition
ON. If the intake air temperature is greater than 80°C (176°F) at
ignition ON, then the transmission default temperature equals ECT + 10°C. |
| • | If none of the above conditions exist, then the transmission
default temperature is 80°C (176°F) |
|
P0713
| Automatic Transmission
Fluid Temperature Sensor-High Input
| D
|
| • | DTC P0713 is stored in PCM memory |
| • | If any engine coolant temperature sensor codes are set, then the
transmission defaults to a temperature of 132°C (269°F) |
| • | If the engine coolant temperature is greater than 110°C (230°F),
then the transmission will default to a temperature of 132°C (269°F).
This will enable Transmission Hot Mode. The transmission remains in Hot Mode
until the engine coolant temperature drops below 105°C (221°F) If
the engine run time is less than 5 min, then the transmission defaults
to the intake air temperature at ignition ON. |
| • | If the engine coolant temperature is between 70°-110°C
(158°-230°F), then the transmission default temperature equals ECT - 10°C
when the intake air temperature is less than 80°C (176°F) at ignition
ON. If the intake air temperature is greater than 80°C (176°F) at
ignition ON, then the transmission default temperature equals ECT + 10°C. |
| • | If none of the above conditions exist, then the transmission
default temperature is 80°C (176°F) |
|
P0716
| Automatic Transmission
Input Speed Sensor-Range/Performance
| A
|
| • | DTC P0716 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Disable upshift, steady state and garage shift adapts |
| • | Calculate ISS from VSS and commanded gear |
|
P0717
| Automatic Transmission
Input Speed Sensor-No Signal
| A
|
| • | DTC P0716 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable upshift, steady state and garage shift adapts |
| • | Calculate ISS from VSS and commanded gear |
|
P0719
| TCC Brake Switch Circuit
Low
| C
|
| • | DTC P0719 is stored in PCM memory |
| • | SERVICE ELECTRICAL SYSTEM displays |
| • | Disable garage shift adapts |
| • | Extended travel or brake lamp switch is used by the PCM |
|
P0724
| TCC Brake Switch Circuit
High
| C
|
| • | DTC P0724 is stored in PCM memory |
| • | SERVICE ELECTRICAL SYSTEM displays |
| • | Disable garage shift adapts |
| • | Extended travel or brake lamp switch is used by the PCM |
|
P0730
| Incorrect Gear Ratio
| C
|
| • | DTC P0730 is stored in PCM memory |
| • | SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable upshift, steady state and garage shift adapts |
|
P0741
| Torque Converter Clutch
System Stuck OFF
| A
|
| • | DTC P0741 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit 4th gear in Hot Mode |
|
P0742
| Torque Converter Clutch
System Stuck ON
| A
|
| • | DTC P0742 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit 4th gear in Hot Mode |
|
P0748
| Pressure Control Solenoid
Electrical
| C
|
| • | DTC P0748 is stored in PCM memory |
| • | SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable upshift, steady state and garage shift adapts |
|
P0751
| 1-2 Shift Solenoid Valve
Performance
| A
|
| • | DTC P0751 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable steady state and garage shift adapts |
|
P0753
| 1-2 Shift Solenoid Valve
Electrical
| A
|
| • | DTC P0753 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable steady state and garage shift adapts |
|
P0756
| 2-3 Shift Solenoid Valve
Performance
| A
|
| • | DTC P0756 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable steady state and garage shift adapts |
|
P0758
| 2-3 Shift Solenoid Valve
Electrical
| A
|
| • | DTC P0758 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable steady state and garage shift adapts |
|
P1810
| Automatic Transmission
Fluid Pressure Manual Valve Position Switch
| A
|
| • | DTC P1810 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable steady state and garage shift adapts |
|
P1811
| Maximum Adapt and Long
Shift
| C
|
| • | DTC P1811 is stored in PCM memory |
| • | SERVICE TRANSMISSION displays |
| • | Inhibit torque management |
| • | Disable upshift, steady state and garage shift adapts |
|
P1814
| Torque Converter Overstress
| D
| DTC P1814 is stored in PCM memory
|
P1860
| Torque Converter Clutch
Solenoid Valve Electrical
| A
|
| • | DTC P1860 is stored in PCM memory |
| • | SERVICE ENGINE SOON, SERVICE TRANSMISSION displays |
| • | Inhibit 4th gear in Hot mode |
|
*DTC Types:
| • | A-Emission-related, turns the MIL ON after the first failure. |
| • | B-Emission-related, turns the MIL ON after two consecutive
trips with failure. |
| • | C-Non-emission-related, message displayed. |
| • | D-Non-emission-related, no lamps and no message. |
|
