Wipers Delay Mode Inoperative Pulse
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Wiper/Washer System Check performed? | -- | Go to Step 2 | |
2 |
Does the resistance vary within the specified range? | 39 kohms to 680 kohms | Go to Step 4 | Go to Step 3 |
3 | Replace the wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement . Is the replacement complete? | -- | -- | |
4 |
Is the measurement within the specified values? | 10.5-15.5 V | Go to Step 6 | Go to Step 5 |
5 | Repair the open in CKT 477. Is the repair complete? | -- | -- | |
6 | Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement . Is the replacement complete? | -- | -- |
Wipers Delay Mode Inoperative Rainsense
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Wiper/Washer System Check performed? | -- | Go to Step 2 | |
2 |
Are the wipers operating? | -- | Go to Step 3 | |
3 | Set the wiper switch to the middle AUTO DELAY position. Does the wiper system operate like a delay system? | -- | Go to Step 5 | Go to Step 4 |
4 | Set the wiper switch to the next-higher sensitivity position (towards OFF). Did an instant wipe occur when increasing sensitivity? | -- | Go to Step 6 | |
5 |
Did an instant wipe occur when moving the wiper switch from the maximum sensitivity position (closest to OFF) to the second highest sensitivity position? | -- | Go to Step 7 | Go to Step 14 |
6 | Replace the rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
7 |
Is the test light on? | -- | Go to Step 11 | Go to Step 8 |
8 | Connect a test light from the rainsense module connector (harness side), terminal 8, to ground. Is the test light on? | -- | Go to Step 9 | Go to Step 10 |
9 | Repair the open in CKT 851. Is the repair complete? | -- | -- | |
10 | Repair the open in CKT 43. Is the repair complete? | -- | -- | |
11 |
Is there continuity? | -- | Go to Step 12 | Go to Step 13 |
12 | Replace the rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
13 | Repair the open in CKT 482. Is the repair complete? | -- | -- | |
14 | Move the wiper switch from the second highest sensitivity position to the third highest sensitivity position. Did an instant wipe occur? | -- | Go to Step 15 | Go to Step 16 |
15 | Replace the rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
16 | Move the wiper switch from the third highest sensitivity position to the fourth highest sensitivity position. Did an instant wipe occur? | -- | Go to Step 17 | Go to Step 18 |
17 | Inspect for dirty glass or a clouded rainsense module attachment. If the windshield is clean and the adhesive tape is not clouded, replace the rainsense module. Refer to Outside Moisture Sensor Replacement . Is the repair or replacement complete? | -- | -- | |
18 | Move the wiper switch from the fourth highest sensitivity position to the fifth highest sensitivity position. Did an instant wipe occur? | -- | Go to Step 20 | Go to Step 19 |
19 | Replace the rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
20 |
Is the replacement complete? | -- | -- |
