Tools Required

Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.

Caution: Failure to prep the area prior to the application of primer may cause insufficient bonding of urethane adhesive. Insufficient bonding of urethane adhesive may allow unrestrained occupants to be ejected from the vehicle resulting in personal injury.

Caution: At least 24 hours are required for complete curing of repair material. The repair area should not be physically distrubed until after that time. Insufficient curing of urethane adhesive may allow unrestrained occupants to be ejected from the vehicle resulting in personal injury.

Caution: When replacing stationary windows, use Urethane Adhesive Kit GM P/N 12346392 (Canadian P/N 10952983), or a urethane adhesive system meeting GM Specification GM3651G, to maintain original installation integrity. Failure to use the urethane adhesive kit will result in poor retention of the window which may allow unrestrained occupants to be ejected from the vehicle resulting in personal injury.

1. Mask off the area around the rear window to: protect painted surfaces, the headliner, and as an aid in cleanup after installation.
2. Open the rear compartment in order to access the lower reveal molding.



3. Remove the rear window lower reveal molding (2) by removing the fasteners (1) securing the molding to the body.
4. Remove the rear sail panels. Refer to Sail Panel Replacement in Interior Trim.



5. Disconnect the rear window defogger left electrical connector.



6. Disconnect the rear window defogger right electrical connector.



7. Using a sharp utility knife, make a preliminary cut around perimeter of the rear window, cut as close to edge of the rear window as possible.



8. When cutting out the glass, apply a spray mist of water around the surface to aid in the removal.

Cut out the rear window keeping the blade as close to edge of the rear window as possible using J 24402-A




9. With the aid of an assistant use suction cups to lift the rear window from the opening.
10. The following components may reveal the causes of a broken rear window:

•	The flange of the rear window opening

•	The rear window reveal molding

•	The rear window

11. Inspect the condition of the rear window opening and the adhesive bead in order to determine which installation method you will use. Refer to Short Method Description or Extended Method Description .
12. Look for any of the following conditions in order to prevent any future breakage to the rear window:

•	A high weld

•	Solder spots

•	Hardened spot weld sealer

•	Any obstruction or irregularity in the pinchweld flange

Important: If corrosion of the pinchweld flange is present, or if sheet metal repairs or replacements are required, refinish the pinchweld flange in order to present a clean primer only surface. If repairs to the paint are required, mask the flange bonding area prior to the application of the color coat in order to provide a clean primer only surface. Use material such as BASF DE17®, DuPont 2610®, and PPG DP40® products are approved for this application.

13. After repairing the opening as indicated, perform the following steps:
14. Remove no more of the window urethane adhesive than necessary in order to maintain the original shape. This will ensure the proper clearance between the window and the pinchweld flange of the opening.
15. Clean the rear window and pinchweld flange with a clean, dampened cloth using GM Glass Cleaner P/N 1050427 or isopropyl alcohol in order to clean the surface of the rear window and the pinchweld flange of the excess urethane adhesive.

1. After repairing the opening as indicated, perform the following:
2. Thoroughly shake the primers that are provided in urethane adhesive kit GM P/N 12346392, or equivalent.



3. Use a new dauber to apply the pinchweld primer (Black #3) to the primed surface on the pinchweld flange and to any exposed painted surfaces or any scratches in the metal in the bonding area.
4. Allow approximately 10 minutes drying time for the pinchweld primer (Black #3).



5. Install the new rear window reveal molding.

Start from the center and hand press the rear window reveal molding onto the rear window.




6. With the aid of an assistant, dry fit the rear window in the opening in order to determine the correct position.
7. Use masking tape in order to mark the location of the rear window in the opening.
8. Slit the masking tape at the top edge of the rear window.



9. With the aid of an assistant remove the rear window.
10. Place the rear window inside up on a clean, protected surface.
11. If the you reuse the original rear window, remove all but approximately 2 mm(3/64 in.) of the existing urethane adhesive from the rear window surface, using a utility knife or equivalent.
12. Clean the inside surface of the rear window to which urethane adhesive will be applied (around the edge of the inside surface) by wiping with a clean cloth dampened with GM Glass Cleaner P/N 1050427 or isopropyl alcohol, then allowing to air dry.
13. If the extended installation method is being performed, do the following:

13.1.

Remove all but approximately 2 mm (3/64 in.) of the existing bead of adhesive from the pinchweld flange.

13.2.

It is not necessary to remove all the traces of the urethane adhesive, but all mounds or loose pieces should be removed.

13.3.

Thoroughly shake the pinchweld primer (#3 black).

13.4.

Use a new dauber in order to apply the pinchweld primer (#3 black) to exposed painted surfaces or scratches in the pinchweld flange in the bonding area.

13.5.

Allow approximately 10 minutes drying time for the pinchweld primer (#3 black).

Important: Use the following procedure:

14. Use care when applying the stationary window prep (#1 clear) in order to prevent the stationary window prep (#1 clear) from running into the vision area of the rear window. This stationary window prep (#1 clear) may stain the viewing area of the rear window if not applied evenly and dries almost instantly.



15. If installing a new non encapsulated window, perform the following steps:
16. Using a new dauber, apply the windshield prep (#1 clear) to an area approximately 10-16 mm (3/8-5/8 in) around the entire perimeter of the rear window inner surface (reference the illustration of the primer/bonding areas).
17. Apply the stationary window prep (#1 clear) to any exposed edges of the window.
18. Immediately wipe the primed area with a clean lint free cloth.
19. If installing a new encapsulated window, perform the following steps:
20. Using a new dauber, apply the windshield prep (#4 clear) to an area approximately 10-16 mm (3/8-5/8 in) around the entire perimeter of the glass inner surface of the primer/bonding areas.



21. Thoroughly shake the stationary window primer (#2 black).
22. Using a new dauber, apply the windshield primer (#2 black) to the areas of the stationary window (1) to which prep (#1 clear) was applied.
23. Allow approximately 10 minutes for drying the stationary window primer (#2 black).



24. Prior to application of the urethane adhesive, cut the tip of the applicator nozzle in order to provide the following bead sizes:

•	For the short method, cut the tip in order to provide an adhesive bead of approximately 6.0 mm (1/4 in).

•	For the extended method, cut the tip in order to provide an adhesive bead of approximately 10.5 mm (0.14 in.) wide and 10.5 mm (0.14 in) high.




25. Using a cartridge-type caulking gun, apply a smooth continuous bead of urethane adhesive around the edge of the rear window where the primer was applied.
26. When using the short installation method, apply the urethane adhesive to the existing bead of urethane adhesive on the body.



27. When using the extended installation method, use the edge of the rear window or the inside edge of the reveal molding as a guide for the nozzle in order to apply the urethane adhesive (2) to the inner surface of the stationary window (3).



28. With the aid of an assistant, use rubber suction cups in order to install the rear window in the opening.
29. Align the tape on the rear window and on the body.
30. Press the rear window firmly into place to wet-out and seat the urethane adhesive.
31. Tape the rear window to the body in order to minimize any movement until the urethane adhesive cures.
32. Remove any excess urethane adhesive.




Important: Warm or hot water accelerates the cure of the adhesive. Do not direct a hard stream of high pressure water at the fresh urethane adhesive.

33. Use a soft spray of warm water in order to immediately water test the rear window.
34. Inspect the rear window for leaks.
35. If you found any leaks, use a plastic paddle in order to apply extra urethane adhesive at the leak point.
36. Retest the stationary window for leaks.
37. Complete the following steps in order to properly cure the urethane adhesive:

•	Keep the vehicle at a room temperature of 21° C (70° F) at 30 percent or less relative humidity.

•	Allow a minimum of (6 hours) for the moisture curing urethane adhesive.

•	Allow a minimum of (1 to 1/½ hours) for the chemical curing urethane adhesive.

•	Partially lower a door window in order to prevent pressure build-ups when you close doors prior to the urethane adhesive cure.

•	Do not drive the vehicle until the urethane adhesive is fully cured.

•	Do not use compressed air in order to dry the urethane adhesive.




38. Connect the rear window defogger left electrical connector.



39. Connect the rear window defogger right electrical connector.
40. Install the rear sail panels. Refer to Sail Panel Replacement in Interior Trim.



41. Install the rear window lower reveal molding (2).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

42. Install the rear window lower reveal molding fasteners (1).

Tighten
Tighten the 4 fasteners to 2 N·m (18 lb in).

43. Close the rear compartment lid.
44. Wipe the rear window area with a clean, dampened cloth using GM Glass Cleaner P/N 1050427 or isopropyl alcohol in order to clean the surface of the rear window of the excess urethane adhesive.

Allow to air dry.