Tools Required

1. Install the J 28467-A in order to support the engine. Refer to Engine Support Fixture in Engine Mechanical - 4.6L.
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Remove the front tires and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
4. Remove the stabilizer shaft. Refer to Stabilizer Shaft Replacement in Front Suspension.



5. Remove the bolts retaining the steering gear to the engine frame.
6. Remove the ball joints from the steering knuckle. Refer to Lower Control Arm Replacement in Front Suspension.
7. Remove the front air deflector. Refer to Front Air Deflector Replacement in Body Front End.
8. Remove the brake pressure modulator valve. Refer to Brake Pressure Modulator Valve Replacement in Antilock Brake System.



9. Disconnect the road sensing suspension links (1) from the lower control arm ball studs.
10. Remove the A.I.R. Pump. Refer to Secondary Air Injection Pump Replacement in Engine Controls.



11. Remove the brackets (2) retaining the power steering line (1) at the frame.
12. Remove the retainer clips (3) retaining the power steering line (4) along the left side of the engine frame.
13. Using mechanics wire, retain the steering gear to the body.



14. Lower vehicle until engine frame rests on suitable jack stands or J 39580 .



15. Remove the fastener retaining the front engine mount to the engine frame.



16. Remove the fasteners retaining the rear transaxle mount (1) to the engine frame.



17. Remove the engine frame insulator bolts (3) retaining the engine frame (2) to the vehicle.
18. Raise vehicle away from engine frame.



19. Separate the engine frame insulators from the engine frame in the following order:

19.1.

Remove the bolts (2) from the engine frame (1).

19.2.

Remove the lower insulator retainer (3) from the lower insulator (4).

19.3.

Remove the lower insulator (4) from the engine frame (1).

19.4.

Remove the retainer (7) and the upper spacer (6) from the upper insulator (5).

Remove the upper insulator (5) from the engine frame (1).

20. Remove the control arms. Refer to Lower Control Arm Replacement in Front Suspension.

1. Install the control arms. Refer to Lower Control Arm Replacement in Front Suspension.



2. Assemble the engine frame insulators to the engine frame in the following order:

2.1.	Install the upper insulator (5) into the engine frame (1).

2.2.	Install the retainer (7) and the upper spacer (6) onto the upper insulator (5).

2.3.	Install the lower insulator (4) into the engine frame (1).

2.4.	Install the lower insulator retainer (3) onto the lower insulator (4).

2.5.	Install the bolts (2) into the engine frame (1).

3. Lower the vehicle to the engine frame.



4. Using dowel pins in the alignment holes (1), align the engine frame (2) with the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the engine frame insulator retainer bolts (3) in order to retain the engine frame (2) to the vehicle.

Tighten
Tighten the retainers to 191 N·m (141 lb ft).




6. Raise the vehicle away from the jack stands supporting the engine frame or J 39580 .



7. Install the fasteners in order to retain the rear transaxle mount (1) to the bracket.

Tighten
Tighten the retainers to 50 N·m (37 lb ft).




8. Install the fastener in order to retain the front engine mount to the engine frame.

Tighten
Tighten the fastener to 41 N·m (30 lb ft).




9. Install the fasteners in order to retain the steering gear to the engine frame.

Tighten
Tighten the retainer bolt to 120 N·m (89 lb ft).




10. Install the bracket (2) to retain the power steering line (1) at the engine frame.
11. Install the retainer clips (3) retaining power steering line (4) along engine frame rail.
12. Install the A.I.R. Pump to the vehicle. Refer to Secondary Air Injection Pump Replacement in Engine Controls.
13. Install the brake pressure modulator valve. Refer to Brake Pressure Modulator Valve Replacement in Antilock Brake System.



14. Install the real time dampening sensor links (1) to the lower control arm ball studs.
15. Install the front air deflector. Refer to Front Air Deflector Replacement in Body Front End.
16. Install the ball joints to the steering knuckle. Refer to Lower Control Arm Replacement in Front Suspension.
17. Install the front tires and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
18. Install the stabilizer shaft. Refer to Stabilizer Shaft Replacement in Front Suspension.
19. Lower the vehicle.
20. Remove the engine support fixture. Refer to Engine Support Fixture in Engine Mechanical - 4.6L.