GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2002 🢒 Seville 🢒 Body and Accessories 🢒 Lighting Systems 🢒 DTC B2420

Circuit Description

The twilight delay pot sensor is a potentiometer. The instrument panel integration module (IPM) determines the control setting based on the voltage from the twilight delay pot sensor. As the resistance of the twilight delay switch varies, the voltage input to the IPM changes. The IPM performs a diagnostic test on the twilight delay input circuit every 150 milliseconds.

Conditions for Running the DTC
    • The ignition switch is in the ON position.
    • The IP dimmer switch is set to MAXIMUM.
    • The headlamps are ON.

Conditions for Setting the DTC

The IPM will set the DTC B2420 when it detects that twilight delay input is less than 5 Counts or greater than 250 counts for 3 consecutive tests.

Action Taken When the DTC Sets

The IPM will assume that the twilight switch is on and the twilight delay indicates the maximum.

Conditions for Clearing the DTC

The IPM sees that the twilight delay input is between 5 and 250 Counts.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Tests for the proper operation of the circuit in the high voltage range.

    2.

  2. Tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to voltage.

    3.

  3. Tests for a short to ground in the 5 volt reference circuit.

Step

Action

Value(s)

Yes

No

Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics

1

Did you perform the Lighting Systems Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Lighting Systems

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Twilight Delay Pot data parameter in the Instrument Panel Module Open/Short Data list.

Does the scan tool indicate that the Twilight Delay Pot data parameter is within the specified range?

5-250 Counts

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the headlamp switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Twilight Delay Pot data parameter.

Does the scan tool indicate that the Twilight Delay Pot data parameter is greater than the specified value?

250 Counts

Go to Step 4

Go to Step 8

4

  1. Turn OFF the ignition.
  2. Connect a 3 amp fused jumper wire between the signal circuit of the twilight delay sensor and the sensors return circuit of the twilight delay sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Twilight Delay Pot data parameter.

Does the scan tool indicate that the Twilight Delay Pot data parameter is less than the specified value?

5 Counts

Go to Step 5

Go to Step 9

5

  1. Turn OFF the ignition.
  2. Disconnect the fused jumper wire.
  3. Connect a 3 amp fused jumper wire between the 5 volt reference circuit of the twilight delay sensor and the signal circuit of the twilight delay sensor.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, observe the Twilight Delay Pot data parameter.

Does the scan tool indicate that the Twilight Delay Pot data parameter is greater than the specified value?

250 Counts

Go to Step 7

Go to Step 6

6

Test the 5 volt reference circuit of the twilight delay sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

7

Test the 5 volt reference circuit of the twilight delay sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 11

8

Test the signal circuit of the twilight delay sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

9

Test the signal circuit of the twilight delay sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 10

10

Test the sensors return circuit of the twilight delay sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

11

Inspect for poor connections at the harness connector of the headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 13

12

Inspect for poor connections at the harness connector of the instrument panel integration module (IPM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 14

13

Replace the headlamp switch. Refer to Headlamp Switch Replacement .

Did you complete the replacement?

--

Go to Step 15

--

14

Important:: Perform the setup procedure for the Instrument Panel Integration Module (IPM). Refer to Body Control Module (BCM) Programming/RPO Configuration .

Replace the IPM. Refer to Instrument Panel Module Replacement in Body Control System.

Did you complete the replacement?

--

Go to Step 15

--

15
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK