Tools Required

1. Recover the refrigerant from the system. Refer to Refrigerant Recovery and Recharging .
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
3. Remove the accessory drive belt from the compressor. Refer to Drive Belt Replacement in Engine Mechanical.
4. Remove the front air deflector. Refer to Front Air Deflector Replacement in Body Front End.
5. Remove the right front tire. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
6. Remove the right wheelhouse extension. Refer to Front Bumper Fascia Extension Replacement in Body Front End.
7. Disconnect the brake line retaining clip from the frame in order to allow movement of the brake lines during removal of the A/C compressor.



8. Disconnect the suction hose fitting from the compressor.

Important: Seal the A/C compressor suction and discharge ports after the hoses are removed in order to keep contaminants from entering the A/C compressor, and to keep oil from draining out of the A/C compressor during removal.

All A/C lines, hoses and components should always be sealed after component removal in order to avoid excessive moisture contamination to the A/C system during servicing.



9. Disconnect the discharge hose fitting from the compressor.



10. Disconnect the compressor electrical connector.
11. Remove the lower alternator bolt.



12. Remove the A/C compressor mounting fasteners (1, 2, 3, 4).



13. Remove the A/C Compressor (2) mounting stud (1).



14. Rotate the A/C compressor, in order to allow the A/C compressor to exit through the wheelhouse extension opening.
15. Remove the A/C compressor.
16. Balance the compressor oil. Refer to Compressor Oil Balancing .

1. Install the compressor through the wheelhouse extension opening.
2. Rotate the compressor in order to fit the compressor though the wheel house extension opening.



3. Install A/C compressor (2) mounting stud (1).
4. Install the lower alternator bolt.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the A/C compressor mounting fasteners (1, 2, 3, 4) and hand tighten the fasteners.

Tighten the fasteners in the following sequence:

Tighten

1. Tighten the A/C compressor mounting nut (1) to 50 N·m (37 lb ft).
2. Tighten the A/C compressor mounting bolts (2, 3) to 50 N·m (37 lb ft).
3. Tighten the last A/C compressor mounting bolt (4) to 25 N·m (18 lb ft).



6. Connect the compressor electrical connector.



7. Connect the discharge hose fitting to the compressor.

Tighten
Tighten the discharge hose fitting to the compressor to 20 N·m (15 lb ft).




8. Connect the suction hose fitting to the compressor .

Tighten
Tighten the suction hose fitting to the compressor to 20 N·m (15 lb ft).

9. Connect the brake lines and the retaining clips to the frame.
10. Install the accessary drive belt on to the compressor. Refer to Drive Belt Replacement in Engine Mechanical.
11. Install the facia extension. Refer to Front Bumper Fascia Extension Replacement in Body Front End.
12. Install the front air deflector. Refer to Front Air Deflector Replacement in Body Front End.
13. Install the right front tire. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
14. Reconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
15. Recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
16. Leak test the fittings of the repaired or reinstalled component using J 39400-A .